The E-Lab Navigator says that the OS2007 FA Port Flag Bit is "optional" in Linux configurations, but it doesn't say optional for what? How do I find that?
There are no footnotes, which sometimes there are.
I searched in PowerLink, but I can't find an answer.
I did find that somebody had asked this very same question for VMware, but I didn't get a good answer there, either. I was referred to Primus emc173498 and emc71378, which told me, respectively, that the OS2007 flag is required in HP-UX 11v3 for automatic device discovery, and has something to do with port sharing in heterogenous environments (whatever that means) on VMware.
I dont know about your array microcode.But please go through this to get an idea--
1. What are the "port flags" settings for 5875 Enginuity and what do they mean?
Port flags in Enginuity are used to set behavior that enables a connected server/operating system combination to work with the Symmetrix port (seen as a disk drive to the server) and to optimize the operation of that server and “disk” combination. Symmetrix VMAX with 5875 is delivered with the correct default port flag settings for most users so that few or no changes will be needed during installation of the new system.
EMC strives to make setup and operation of our products as simple and easy as possible. We believe that Enginuity 5875 for VMAX is delivered to you with correct default port flag settings for most users and that few or no changes will be needed during installation of your new system. Here is a summary of the default flag settings for the most popular operating systems. and changes required by some of those operating systems.
2. What Servers can connect to 5875 Enginuity without changing Port Flags?
Operating Environment
Port Settings
EMC Celerra
Enable 'ARB' and 'D' flags
IBM AIX
5875 Defaults, Unchanged
INM i
Enable 'AS4' flag
LINUX
Enable 'D' flag
Hewlett-Packard OpenVMS
Enable 'OVMS' flag
Hewlett-Packard True64
Enable 'OVMS' flag, Disable 'SC3 flag
Hewlett-Packard HP-UX 11i V1 &V2
Enable 'V' flag, Disable 'SC3' and 'OS07' flag
Hewlett-Packard HP-UX 11i V3
Enable 'V' flag, Disable 'SC3'
Microsoft Windows Server 2008
5875 Defaults, Unchanged
Microsoft Windows Server 2003
5875 Defaults, Unchanged
Oracle Solaris
5875 Defaults, Unchanged
VMware ESX
5875 Defaults, Unchanged
3. What are some additional considerations?
Directly connecting servers to the array, not using switches or other SAN components, you are using Fibre-Channel Arbitrated Loop. This requires that the PP flag to be DISABLED and a Loop ID assigned to a particular number ranging from 0-126. FC-AL is used in certain markets and with some specialty servers.
Using Fujitsu (formerly Siemens), Novell Netware or Teradata systems, please look at the support matrix at EMC.com for specific recommendations.
Use of Clusters can impact port flag settings. Please look at ELab's Host Connectivity Guide of the particular operating system for information for details of a cluster's required port flag settings.
4. Port Flag usage notes:
These new default values are in some cases different from the 5874 settings. Connection of a server to both 5874 and 5875 Enginuity may require changes to the 5875 defaults or the user to set the flags at the Initiator to match the previously installed array with its existing connection to the server. Note in general that changes of the flags will not become effective until the host is rebooted or FC connectivity is bounced.
Script behavior can change based upon these new 5875 default Port Flag settings. Existing scripts should be tested to ensure port flag settings and scripts are compatible.
Your VMAX is set to operate with the ACLX flag ENABLED, which enables masking of specific devices to specific ports on the array. Note that user must still provision ACLX volumes to enable hosts management via Solution Enabler.
The OS07 flag, ENABLED by default, can generate warnings (I/O retry) on Solaris, OpenVMS, and some other hosts. Some high performance or sensitive applications may be degraded by the additional retry. EMC believes we support the SCSI standard correctly, and retries should not occur, but that said, it can happen on some systems. Such environments should DISABLE this flag. Although the OS07 flag is on by default, specifically for VMWARE ESX this setting may need to be disabled.
Note: that if you DISABLE the OS07 flag and wish to re-ENABLE it, you must be sure that the SPC2 flag is ENABLED first. Also note that the SPC2 flag value should not be changed from DISABLED to ENABLED on installed servers as it changes the disk name utilized by the server and the disks will no longer be visible to that server.
If SCSI-3 persistent device reservation bit (“PER”) is used (note that this flag is assigned to devices and not to ports and so is not covered by this document), then the SC3 bit should be set. Please refer to the Elab Host Connectivity Guide for documentation on the platforms that can utilize the SCSI-3 reservation bit.
For additional information regarding to port flags, specific flags for a given server, impacts of changing flags and any other known issues, please go to EMC.com and search PRIMUS for additional port flag information.
5. How did 5875 EnginuityPort Flag Defaults Change from earlier releases?
The following is the table of default settings for the commonly set flags for 5875 Enginuity versus other recent Enginuity releases:
Flag
Enginuity 5773
Enginuity 5874
Enginuity 5875
PP
Enabled
Enabled
Enabled
UWN
Enabled
Enabled
Enabled
EAN
Enabled
Enabled
Enabled
C
Enabled
Enabled
Enabled
SPC2
Enabled
Enabled
Enabled
OS07
Disabled
Disabled
Enabled
ACLX
Disabled
Disabled
Enabled
SC3
Disabled
Disabled
Enabled
6.What are the port flag descriptions?
Flags come in two types. The first type are flags set only on the array’s storage port. These flags affect the connectivity behavior of all servers connected to that port. The second type of flags can be set per storage port or initiator group, a group defined on the array as one or more initiators (HBAs) for a given server. With this type, the flags settings for the initiator group override, for the group, the settings on the port itself. In this way, a port can be shared by servers with different flag requirements.
The following table list where the flags should be set:
Flag
Flag Description
Flags set only at the StoragePort
Flags that can be set at the StoragePort or Initiator Groups
PP
When enabled, specifies a point-to-point (direct or switched) topology in the initialization sequence. When disabled (default), it is initialized as an arbitrated loop.
YES
N/A
EAN
When enabled, allows two fibre ports to handshake and settle on an optimal speed for data transfer.
YES
N/A
ACLX
When this flag is set, it enables the Initiator Groups/Access Logix1 function on the port.
YES
N/A
UWN
When enabled, ensures unique World Wide Names (WWNs) within the fibre environment by incorporating Symmetrix serial numbers and port numbers for each WWN. Enabled by default for all environment configuration changes and new environments. When disabled, WWNs do not have to be changed.
YES
N/A
NP
When enabled along with the Hard Addressing flag, the Fibre Channel director only uses hard-assigned addressing when it initializes the loop, otherwise, soft-assigned addressing is used during loop initialization (the default).
YES
N/A
C
When enabled, this flag causes the serial number of a specific volume to be the same regardless of the port on which it is visible.
N/A
YES
V
When enabled along with the Disk_Array flag for HP-UX hosts, the volume setaddressing mode is selected. VSA mode allows octal addressing.
N/A
YES
ARB
Typical behavior on a SCSI bus reset is to propagate the reset to all channels that share devices mapped to the port that received the reset. When this bit is set, the reset only occurs to the port on which it is received, and is not broadcasted.
N/A
YES
D
When this flag is enabled, a Unit Attention (UA) that is propagated from another director does not flush the queue for this device on this director. Used for hosts that do not expect the queue to be flushed on a SCSI 0629 sense (only on a Hard Reset).
N/A
YES
SC3
When this flag is set, it alters the Inquiry data returned by any device on the port to report that Symmetrix supports SCSI -3. If this flag is not set, it reports that SCSI-2 is the supported protocol. This flag also enable the support for Auto Contingence Allegiance which is required by IBM AIX.
N/A
YES
OS07
The effect of the OS07 setting can be summarized as follows: 1. Automated device discovery of newly configured devices and/or device paths. 2. Automated creation of DSFs (device special files) for newly configured devices. 3. Automated detection and adaptation of device attribute changes including LUN 4. Capacity change event.
N/A
YES
SPC2
This flag enables the support for SPC-2 SCSI standard that are recommended for FC, FCoE, and iSCSI connectivity
N/A
YES
AS4
This flag should be enabled for any AS/400 (IBM i) hosts connecting to the port.
"Optional" (in this circumstance) means that the flag is not required by the operating system in question (e.g., Linux) BUT it can be enabled without any adverse affects.
So if the FA port is being shared with a host that DOES require OS2007 (e.g, Windows 2008 or HP-UX 11i v3), you could (say) enable OS2007 at the bin file level on the FA port and attach HBA's from both hosts (say Linux & Windows hosts) to this FA. With no need to use Solutions Enabler set hba_flags (or equivalent) to disable the OS2007 flag for the WWN of the Linux HBA.
A much better term would be "Don't Care" rather than "Optional"
MorbidAngel1
62 Posts
1302
0
Posted November 14th, 2011 16:00
Hi Stuart,
I dont know about your array microcode.But please go through this to get an idea--
Port flags in Enginuity are used to set behavior that enables a connected server/operating system combination to work with the Symmetrix port (seen as a disk drive to the server) and to optimize the operation of that server and “disk” combination. Symmetrix VMAX with 5875 is delivered with the correct default port flag settings for most users so that few or no changes will be needed during installation of the new system.
EMC strives to make setup and operation of our products as simple and easy as possible. We believe that Enginuity 5875 for VMAX is delivered to you with correct default port flag settings for most users and that few or no changes will be needed during installation of your new system. Here is a summary of the default flag settings for the most popular operating systems. and changes required by some of those operating systems.
2. What Servers can connect to 5875 Enginuity without changing Port Flags?
Operating Environment
Port Settings
EMC Celerra
Enable 'ARB' and 'D' flags
IBM AIX
5875 Defaults, Unchanged
INM i
Enable 'AS4' flag
LINUX
Enable 'D' flag
Hewlett-Packard OpenVMS
Enable 'OVMS' flag
Hewlett-Packard True64
Enable 'OVMS' flag, Disable 'SC3 flag
Hewlett-Packard HP-UX 11i V1 &V2
Enable 'V' flag, Disable 'SC3' and 'OS07' flag
Hewlett-Packard HP-UX 11i V3
Enable 'V' flag, Disable 'SC3'
Microsoft Windows Server 2008
5875 Defaults, Unchanged
Microsoft Windows Server 2003
5875 Defaults, Unchanged
Oracle Solaris
5875 Defaults, Unchanged
VMware ESX
5875 Defaults, Unchanged
3. What are some additional considerations?
4. Port Flag usage notes:
Note: that if you DISABLE the OS07 flag and wish to re-ENABLE it, you must be sure that the SPC2 flag is ENABLED first. Also note that the SPC2 flag value should not be changed from DISABLED to ENABLED on installed servers as it changes the disk name utilized by the server and the disks will no longer be visible to that server.
For additional information regarding to port flags, specific flags for a given server, impacts of changing flags and any other known issues, please go to EMC.com and search PRIMUS for additional port flag information.
5. How did 5875 Enginuity Port Flag Defaults Change from earlier releases?
The following is the table of default settings for the commonly set flags for 5875 Enginuity versus other recent Enginuity releases:
Flag
Enginuity 5773
Enginuity 5874
Enginuity 5875
PP
Enabled
Enabled
Enabled
UWN
Enabled
Enabled
Enabled
EAN
Enabled
Enabled
Enabled
C
Enabled
Enabled
Enabled
SPC2
Enabled
Enabled
Enabled
OS07
Disabled
Disabled
Enabled
ACLX
Disabled
Disabled
Enabled
SC3
Disabled
Disabled
Enabled
6. What are the port flag descriptions?
Flags come in two types. The first type are flags set only on the array’s storage port. These flags affect the connectivity behavior of all servers connected to that port. The second type of flags can be set per storage port or initiator group, a group defined on the array as one or more initiators (HBAs) for a given server. With this type, the flags settings for the initiator group override, for the group, the settings on the port itself. In this way, a port can be shared by servers with different flag requirements.
The following table list where the flags should be set:
Flag
Flag Description
Flags set only at
the Storage Port
Flags that can be set at
the Storage Port or
Initiator Groups
PP
When enabled, specifies a point-to-point (direct or switched)
topology in the initialization sequence. When disabled (default),
it is initialized as an arbitrated loop.
YES
N/A
EAN
When enabled, allows two fibre ports to handshake
and settle on an optimal speed for data transfer.
YES
N/A
ACLX
When this flag is set, it enables the Initiator
Groups/Access Logix1 function on the port.
YES
N/A
UWN
When enabled, ensures unique World Wide Names (WWNs)
within the fibre environment by incorporating Symmetrix serial
numbers and port numbers for each WWN. Enabled by default
for all environment configuration changes and new environments.
When disabled, WWNs do not have to be changed.
YES
N/A
NP
When enabled along with the Hard Addressing flag, the
Fibre Channel director only uses hard-assigned addressing
when it initializes the loop, otherwise, soft-assigned
addressing is used during loop initialization (the default).
YES
N/A
C
When enabled, this flag causes the serial number
of a specific volume to be the same regardless of
the port on which it is visible.
N/A
YES
V
When enabled along with the Disk_Array flag
for HP-UX hosts, the volume setaddressing mode
is selected. VSA mode allows octal addressing.
N/A
YES
ARB
Typical behavior on a SCSI bus reset is to propagate the reset to
all channels that share devices mapped to the port that received
the reset. When this bit is set, the reset only occurs to the port on
which it is received, and is not broadcasted.
N/A
YES
D
When this flag is enabled, a Unit Attention (UA) that is propagated
from another director does not flush the queue for this device on this
director. Used for hosts that do not expect the queue to be flushed on
a SCSI 0629 sense (only on a Hard Reset).
N/A
YES
SC3
When this flag is set, it alters the Inquiry data returned by any device
on the port to report that Symmetrix supports SCSI -3. If this flag is not
set, it reports that SCSI-2 is the supported protocol. This flag also enable
the support for Auto Contingence Allegiance which is required by IBM AIX.
N/A
YES
OS07
The effect of the OS07 setting can be summarized as follows:
1. Automated device discovery of newly configured devices and/or device paths.
2. Automated creation of DSFs (device special files) for newly configured devices.
3. Automated detection and adaptation of device attribute changes including LUN
4. Capacity change event.
N/A
YES
SPC2
This flag enables the support for SPC-2 SCSI standard that
are recommended for FC, FCoE, and iSCSI connectivity
N/A
YES
AS4
This flag should be enabled for any AS/400 (IBM i)
hosts connecting to the port.
N/A
YES
OVMS
Enabled for an OpenVMS Fibre Channel connection.
N/A
YES