msi

updated

1 year ago

Closed

M

msi

1 Rookie

•

4 Posts

0

16010

September 4th, 2020 05:00

P2415Q, 4K HDMI refresh rate is still 30Hz

Hi all,

I have three P2415Q monitors (from June 2019, June 2019, August 2019).

I have a problem with running the 4K over HDMI with 60Hz refresh rate.

Followed the instructions HERE by severe_edgy

All looks similar on my side as in the instructions linked above, except that when the on screen popup shows up, to Enable/Disable HDMI 1.4, I am able to only Confirm/Decline (green/red). The arrows do not work. After factory reset entering the popup the blue selection in set on DISABLE. After "disabling" next try to open this popup shows the blue selection fixed on the ENABLE option.

When I DISABLE 1.4, I do not see any change in the refresh rate. Checked with three different computers. My cable are labeled as "HIGH SPEED HDMI cable", and as far as I was informed they should support 4k@60Hz over HDMI.

I used the DPs so far, but bought one of the monitors recently, and turned out I am out of DP connections on my laptops, so have to use HDMI. I am planning to buy another P2415Q, as I really like this monitor, but the next one is meant to be used with HDMI as well - with 4K.

When I am entering the menu on the monitor, in the bottom it says: "Resolution: 3840x2160, 30Hz        Maximum: 3840x2160, 60Hz".

I need some help to determine what might be the problem in my setup. Tried the monitor as single one, and did not worked either. I am out of options at the moment.

Please help.

Kind regards,

Marek

(edited)

  • HDCharles

    1 Rookie

    •

    1 Message

    •

    2 Points

    0

    0

    Posted October 21st, 2025 20:02

    for anyone looking for the guide linked by OP, its been moved and everything that comes up in google brings you to a dead page. but you can find the same info HERE.

    note: it worked for me

    (edited)

  • msi

    1 Rookie

    •

    4 Posts

    1

    0

    Posted September 4th, 2020 07:00

    The model for June 2019 for example have following ids:

    S/N: CN-0D8VXF-QDC00-968-0W0B A12

    Date of Mfg: June 2019

    It this really the model from 2015, and does not support 4k@60Hz over HDMI?

    (edited)

  • jphughan

    11 Legend

    •

    13985 Posts

    •

    79931 Points

    8798

    0

    Posted September 4th, 2020 07:00

    @msi  The P2415Q's model naming indicates that it's a 2015 model year display.  Even if you have one manufactured more recently, it was designed back then.  4K 60 Hz requires HDMI 2.0, which didn't exist back then.  So odds are that the P2415Q doesn't support receiving 4K 60 Hz on its HDMI input.  That was true of many early 4K 60 Hz displays; they only supported that signal type over DisplayPort because that was the only standard that supported it at the time.  Going back earlier in time, some QHD/1440p displays only supported 1080p over HDMI for the same reason, namely that HDMI has always been behind DisplayPort in terms of bandwidth capabilities at any given time.  The fact that your on-screen menu only mentions HDMI 1.4 rather than 2.0 is an additional suggestion of this limitation.  If the display actually supported HDMI 2.0, they wouldn't leave that unmentioned and name the "compatibility mode" based on the fallback method.  For example, on early Dell displays that supported DP 1.2, there was a DP 1.2 mode option, and if you disabled that, it limited itself to 1.1.  They didn't have a DP 1.1 mode that when disabled caused the display to run DP 1.2.

  • msi

    1 Rookie

    •

    4 Posts

    8782

    0

    Posted September 4th, 2020 11:00

    One of my monitors have following ids:

    Service Tag:

    Express SVC code:

    S/N: CN-0D8VXF-QDC00-98D0FA8-A13

    Date of Mfg: August 2019

     

    Is this really a model from 2015, and do not have HDMI 2.0 support, even if I am able to enter the menu to ENABLE/DISABLE HDMI 1.4?

     

    Please let me know. If this is the old model, which models do support HDMI 2.0?

  • jphughan

    11 Legend

    •

    13985 Posts

    •

    79931 Points

    8761

    0

    Posted September 4th, 2020 15:00

    @msi  And again, as I said earlier, just having an option called "HDMI 1.4" that you can enable or disable doesn't mean that your display supports HDMI 2.0.  If the display supported HDMI 2.0, the option would probably be called "HDMI 2.0", and disabling it might cause it to run in HDMI 1.4 mode.  But if the option is called "HDMI 1.4", then that is probably the NEWEST revision it supports, and disabling it might cause it to run in HDMI 1.3 or an even older revision.  Typically these mode options exist because some older source devices might not work properly if the display supports and tries to use a newer revision.  But again, normally the name of the option relates to the NEWEST revision of a standard that it supports, so that you can enable full functionality (with potentially reduced compatibility) or disable support for the latest standards to maximize compatibility.  It's just like the DisplayPort example I gave earlier.  When DisplayPort 1.2 was relatively new on the market, some displays had an option called "DP 1.2".  If that was enabled, the display would support DP 1.2.  If it was disabled, then it would only use DP 1.1.  But here again, that option was called DP 1.2, to reflect the newest revision it supported.  It wasn't called "DP 1.1".

  • jphughan

    11 Legend

    •

    13985 Posts

    •

    79931 Points

    8762

    0

    Posted September 4th, 2020 15:00

    @msi  You're not supposed to post Service Tags and Express Service codes on a public forum.  But the way Dell's display model naming/numbering works is that the last two digits are the "model year".  The last two digits of your P2415Q are "15", which means it's a 2015 model year display.  The fact that your particular unit was manufactured relatively recently doesn't mean that it was ever upgraded.  It's sort of like cars.  Typically a manufacturer will do a significant redesign every 6-7 years, but within a given generation's lifecycle, the car might only get minor refreshes/changes, so by the end of that lifecycle it's a bit outdated.

    HDMI 2.0 started arriving on consumer products around late 2017 to mid-2018, so products designed and launched before that likely wouldn't have it.  If you want to verify HDMI 2.0 support, check the documentation of any display you're considering.  For Dell displays, go to support.dell.com, search the display model, and then go to the Documentation page and open the User Guide.  Some older displays didn't list HDMI or DisplayPort revisions, but the documentation of newer displays will.

  • KkrazyM

    11 Posts

    8684

    0

    Posted September 11th, 2020 08:00

    I know this is an old thread, but my P2715Q monitor is showing the highest refresh rate to be 30 hz. It won't let me change it to anything higher. I'm not fluent in technology but it says the monitor is connected to the "Intel(R) HD Graphics P630" display adapter, even though I have another one. I have a second adapter called "Radeon (TM) Pro WX 7100 Graphics." Is there any way I can switch the adapters and "unlock" a higher refresh rate? Thanks @jphughan 

  • jphughan

    11 Legend

    •

    13985 Posts

    •

    79931 Points

    8680

    0

    Posted September 11th, 2020 08:00

    @KkrazyM  Unless your system has display output connectors physically wired to that Radeon GPU, which it might not, the no you can't do that.  However, the P630 supports 4K 60 Hz displays.  So the questions are, what system are you using, and what cable(s)/adapter(s) are you using?

  • KkrazyM

    11 Posts

    8678

    0

    Posted September 11th, 2020 09:00

    KkrazyM_0-1599841052535.png

    I am on a Dell Precision 7720 with a 64-bit operating system. Is there anything specific you need to know? I use an HDMI cable to connect them. @jphughan  Thanks

  • jphughan

    11 Legend

    •

    13985 Posts

    •

    79931 Points

    8673

    1

    Posted September 11th, 2020 09:00

    @KkrazyM  The HDMI cable is the issue.  4K 60 Hz over HDMI requires HDMI 2.0.  That didn't show up on Dell systems until around mid-2018.  I'm pretty sure your system is older than that, and even if it isn't, the P2415Q's model name indicates that it was a 2015 model, which definitely predates HDMI 2.0.  So even if you had an HDMI 2.0 system, that display likely won't accept 4K 60 Hz on its HDMI input.  Get a USB-C to DisplayPort cable instead and you'll be fine.