garyk9gs

updated

11 years ago

G

garyk9gs

3 Posts

0

169819

November 5th, 2013 11:00

Optiplex 3010 - PCI-e Prevent slots from sleeping?

I have an Optiplex 3010 with Win7 pro OS.

I have a Rosewill (RC-305E) 4 port RS232 Serial Card occupying one of the PCI-Express slots on the motherboard.  The serial ports work fine except for when the system is idle.

Leaving everything running, application, serial device connected to the card.  When I come back a couple of hours later, to as much as a day later, the application using the RS232 serial port has stopped working.  It no longer reads the serial device.  Sometimes swtpping the application and then restarting gets everything working again.  Other times I have to re-boot the PC.

I went in to the power settings and have everything set to NOT go to sleep.  It is my understanding that the PCI-Express specification calls for going into sleep mode when idle.  What I want to do is turn this off completely.

Any ideas and thanks for helping.

-GS-

  • 3628

    0

    Posted May 18th, 2015 05:00

    I have experienced many troubles when Serial Cards contain the MOSCHIP chipset on the DELL OptiPlex 3020.   I think you will find the Rosewill RC-305E contains this chipset.  I purchased two Serial Cards both with the same CHIPSET (STARTECH, VANTECH), both MOSCHIP chipset.  Serial devices had been configured for Truck Stop Weight Scale (Fairbanks 9406 series) with continuous Serial Communication with continuous data stream.

    Requirements for my Serial Communication:
    The Scale software installed on the DELL OPTIPLEX passively listens to the COMM PORT communication as long as the COMM Port is open by the software.  The Fairbanks scale send data via serial interface in a constant loop.  What I am finding is the MOS chipset somehow idles over time.   If I close and open the PORT then Serial Communication will continue to passively listen to the Data Stream.

    I have had the following issue with the card:

    -          The Serial Card would Idle after a period of TIME, (5-15 minutes).   Originally though the issue was related to the PCIe power saving specifications but I am sure the issues are attributed to the MOSCHIP as well.  Typically I would have to CLOSE and then REOPEN the port for the serial Card to process the incoming data stream

    -          After a period of time (few days) the card would drop from the OS, (unavailable within Device Mgr).  Attempts at removing the DRIVER, Rebooting, Reinstalling the Driver failed to find the MOSCHIP Serial Card.   To get the card working again required physically reseating the Card in a different PCIe SLOT for the OS to recognize the Serial Card

     Requirements for successful communication: 

    - Disable all Power Saving Settings in BIOS
    - Disable all onboard CommPorts in BIOS
    - Disable all Windows Power Options Features, Specifically:
    -- PCIe Link State Power Management - OFF
    -- USB selective suspending Setting - DISABLE  "this should not be necessary w/ PCIe"

    CORRECTIVE ACTION:  Purchase a Serial Card with PLX/OXFORD OXPCIe952 Chipset.  For my DELL 3020, 7020, 9020 Optiplex machines) I have been using the STARTECH PEX1S1P952 (containing the PLX/Oxford - OXPCIe952 chipset) as this work for my needs. 

    My hope is others my find this helpful.

  • garyk9gs

    3 Posts

    3625

    0

    Posted November 5th, 2013 12:00

    USE USB Serial Adapters and Set the USB Root Hubs and Ports to NOT ALLOW THIS DEVICE TO SHUT OFF TO SAVE POWER.  Set this device to Never Sleep. Always On.

    �

    Hello SpeedStep,

     

    Yes, I'm aware of USB-Serial adapters and the ability to change the power settings to never sleep.  What I'm looking for is a way to do exactly that with the native RS232 PCI Express card that I already have.

    There are a number of reason NOT to use the USB-serial adapters.  I really need the native RS232 type of port.

  • speedstep

    11 Legend

    •

    46969 Posts

    3625

    1

    Posted November 5th, 2013 12:00

    USE USB Serial Adapters and Set the USB Root Hubs and Ports to NOT ALLOW THIS DEVICE TO SHUT OFF TO SAVE POWER.  Set this device to Never Sleep. Always On.

    �

  • LBTech62

    5 Posts

    3625

    0

    Posted November 12th, 2013 20:00

    I wonder if that is PCI Express specifications by design or just only a Dell PC design issue.  I am also in the same boat.  I cannot use the USB to serial converters -- many do not work especially with 64-bit Windows.  I bought two different USB to serial converter cables a few weeks ago for a project -- neither worked with the PC -- the device drivers simply would not install correctly.  We have three Dell OptiPlex 3010 PCs in the same boat -- all are running Windows 7 Pro 64-bit.  Are your PCs also 64-bit?  We have been seriously thinking about reloading the PCs with Windows 7 Pro 32-bit.  Some users even want the old Windows XP Pro PCs back since those PCs never had a problem with those serial devices.

  • Appelbv

    4 Posts

    3625

    0

    Posted January 9th, 2014 07:00

    Hi, We are having the same problem with a card from startech. Type pex2s553lp. Does anyone already have a solution for this? Greets
  • garyk9gs

    3 Posts

    3628

    0

    Posted January 9th, 2014 16:00

    I am the OP.  I never did get this to work.

     

    I ended up buying an FTDI chipset USB-RS232 converter cable from Sabrent.  It works great but I would much rather have had the native RS232 card working.  I'm not a big fan of USB ports in general.

    Good luck!

  • LBTech62

    5 Posts

    3628

    0

    Posted January 11th, 2014 00:00

    You can check the StarTech.com website to see if there are any updates to its drivers.  Since we needed only one serial port, Dell actually has a Serial & PS2 add-in card.  The Dell part number for the Small Form Factor model 3010 is:  Y73TJ.  The Dell OptiPlex 3010 and 3020 come with an onboard serial comm port on the motherboard but without the connector on the outside of the case.  That part gives you one serial comm port.  It works great -- we have never had a problem with the port going dormant with that part from Dell.

  • Appelbv

    4 Posts

    3628

    0

    Posted January 17th, 2014 01:00

    Hi,

    We already installed the latest drivers from the startech website. we have updated the bios and set option deep sleep in S4 and s5 on Disabled. We also block sleep in S3.

    If this is not the solution we are seriously thinking to order the dell part. Our problem comes up randomly. somethimes 1 time a week. some 1 time in 2 weeks.

    Thanks!

  • Appelbv

    4 Posts

    3628

    0

    Posted January 17th, 2014 04:00

    I have called startech to ask if poeple called to startech with this problem. they said when you put the Serial PCI-E 1x card in de 16X slot it will better work. im going to try that.

    Maybe this fix helps for all you people.


    Thanks for the help.

  • Feja

    2 Posts

    510

    0

    Posted July 15th, 2015 08:00

    Hi sdfasdfdasfadsfadsf,

    I too have experienced nothing but trouble with Parallell/Serial Cards with MOSCHIP chipset.

    I have succesfully used Parallell Cards with OXPCIe952 chipset on my Optiplex 7020 Machines, but when I tried the PEX1S1P952 on my Optiplex 3020 Machines to get both parallell and serial ports I can not get the serial port working at all (on Win 64bit).

    I could'nt even get the port to install with the drivers from Startech. I found an old Legacy Serial COM port driver dating back to 2007 and was able to at least install the port, but it still doesn't work.

    Any input as to how you managed to get the serial port working?