UNSOLVED

tablets4fun

updated

11 years ago

T

tablets4fun

26 Posts

0

318261

June 23rd, 2015 12:00

Venue 11 Pro 7140 - experience with Crucial MX200 SSD and Link Power Management?

I've installed a 250GB Crucial MX200 M.2 2260-length SSD (model # CT250MX200SSD6) in my Dell 7140. Having read warnings about Link Power Management problems with other 3rd-party SSDs, I disabled Link Power Management immediately after installing Windows (via a recovery drive) on the MX200.

The drive has been installed and working reliably (light usage) for a couple of weeks, now. I'd like to re-enable Link Power Management, for the power reduction benefits, if it will work reliably with this drive.

If you are successfully running a Crucial MX200 in a 7140 with Link Power Management enabled, please post a reply here, and mention how long it's been running and with what workload. Or if you've run with it enabled and had problems, please also post a reply here. Thanks!

  • 7142

    0

    Posted June 26th, 2015 00:00

    When I installed the MX200 (480gb), I never disabled LPM. It's been running fine for a couple weeks.

  • grefuture

    2 Posts

    7142

    0

    Posted June 28th, 2015 09:00

    Hello! I wanted to know if by chance you could explain how you would get the back cover off of the 7140? I am looking at getting a crucial m.2. drive and I have no idea how to get the back off. I would appreciate it

  • 7152

    0

    Posted June 29th, 2015 10:00

    There's a tiny screw under the MicroSd protective "flap". Remove the screw, then just pop the cover off slowly working your way around the back of the screen with a thin piece of hard plastic (like a guitar pick).

  • tablets4fun

    26 Posts

    7152

    0

    Posted June 29th, 2015 11:00

    I found some youtube videos a couple of months ago. Here are 2 links. There may be more by now. I don't recommend the use of a pocket knife. If you don't already have a set of spudgers, you can get a nice assortment from Amazon for $10 to $20.

  • grefuture

    2 Posts

    7170

    0

    Posted July 2nd, 2015 04:00

    Thank you for your quick reply!  One more question....besides the crucial m.2, are there any oherr drives that might work well with the 7140?  Thanks!

  • tablets4fun

    26 Posts

    7170

    0

    Posted July 2nd, 2015 10:00

    When I researched this a month or two ago, the only other drive people were talking about was a 500GB Transcend, but there were many reports of that drive corrupting data if Link Power Management is on.

  • Stayer123

    1 Message

    7170

    0

    Posted July 15th, 2015 07:00

    I just purchase the crucial 500 GB SSD and I really need some advise on what I need to do to install this SSD. I know how to get the SSD out and plug in the new SSD, but I need help on imaging the old SSD to the New one. I have read several article's on how hard it is to do this. Can you just use one of the new NGFF Enclosure to house the new SSD and then use the USB port to transfer the image of the SSD in use. I would really appreciate some info on this process.  

  • keiths123

    2 Posts

    7170

    0

    Posted February 1st, 2016 08:00

    Might be a bit late on the reply but might be useful for others.

    I have had the crusial 500gb drive in the Venue for around a month no issues at all, link managent is enabled and power usage/ battery life on par with the original sandisk SSD. If anything it is quicker. Make sure you install the Crucial software to check for firmware extra feature etc.

    To transfer there are a couple of options I can think of.

    1) get a usb case for the m.2 drive and drive clone the original to the new one ( crucial supply link for free cloning software) the ssap the disk over

    2) make a disk image of you current drive, and have a copy of the operating system on a bootable device e.g. usb stick. Put the new drive in, boot to the usb and reload a new copy of windows. once done then use the disk image to restore to the drive with all you stuff on it.

  • Atreyiu

    8 Posts

    7170

    0

    Posted February 6th, 2016 20:00

    Hello, recently I have a 7140 with M5Y10. I've noticed that much heated in some occasions , reaching 70 to 80°C . When I browse the internet (now for example) goes from 38 to 43°C, when using OneNote walk between 45 and 50°C , when I walk heavier operations exceeds 55 or 60°C (or more). In your experience , which I think is pretty with this model , it is normal to get used to what should or should seek their review ?. Greetings and thank you in advance for any advice .

  • sarlo100

    1 Message

    1921

    0

    Posted May 20th, 2016 19:00

    The thermal envelope is set for 90 degrees C maximum, and when I push the processor, I find that the temperature will settle in that range.  For most operations, the tablet is in the 35-50 degrees C area.

    Your experiences are not out of the ordinary.