As long as you are going to install an SSD anyway, I would set the controller mode to AHCI, perform a fresh installation of the operating system onto the SSD, then set up the HDDs the way you want to.
Agreed ... you don't want to clone your installation to an SSD ... do a clean install.
There will be no difference between using the drives as non-RAID in RAID mode and in AHCI (non-RAID). If you are doing a clean install anyway, switch to AHCI, if not, then you can leave it as it is.
Drives will not show up in My Computer until they have been initialized/formatted. You do this in Disk Management (right-click [My] Computer, Manage).
When I boot with Win7 installation DVD, it starts pre-load from DVD . Than it seems language setting step. I select language and clisk Install. Installation go stop. Windows says No CD-DVD drive. I click to Browse, I am seeing onlt removable drives. No HDD, no Optical.
I updated Bios. Doesn't changed.
If I install with AHCI mod everything OK.
So T3610 - RAID 1 doen't work. I couldn't install windows with RAID 1
Thank you THEFLASH1932. My problem was installation windows 7 on SSD. If I configure SATA operation as RAID, in first step of installation get error: Required CD/DVD drivers not found.
I research on internet and I found the problem, RAID mode require some driver like you said. I downloaded the dirvers and copied a USB flash disk. Tomorrow I will install with using this USB.
And if you do in on another computer it will say "computer not compatible", dont mind about that and go to C:\Dell\Drivers\HXT48\Drivers\win7\AHCI and copy the folder x32 or x64 (depending on the type of processor you have) to an USB drive. Then you can choose the folder while trying to install Win7 in order to load the drivers for the SSD.
I would recommend that you change the SATA mode to AHCI.
I disconnected the HDD, plugged in the SSD, went into the BIOS and set SATA Operation to AHCI, and booted the Windows 7 Pro installer from a known good USB installation drive. I got the:
"Load Driver
A required CD/DVD drive device driver is missing. If you have ..."
I figured that it wanted some of the Dell Intel chipset drivers, and tried various ones in vain. After some help from Prof Google, I found this thread and tried the Storage-Controller_Driver_HXT48_WN_3.8.0.1111_A04, expanded onto another USB drive, from the location above. This at least led to a:
"Select the driver to be installed"
with an actual entry: "Intel(R) C600 series chipset SATA AHCI Controller ...".
Selecting that and clicking on Next then led to a lot of green progress barring, but after 20 s or so:
"No new devices could be found. Make sure the driver files are correct and located on the driver installation media."
All I could do from here was to cancel installation.
This made me think that the SSD was faulty, so I attached it as a secondary driver to another PC, formatted it, tossed about 1 GB of files onto it, and it worked perfectly.
I then changed the SATA Operation to ATA in the BIOS, and tried installation again. Another "Load Driver" dialog, but this time it found nothing in the Storage-Controller_Driver_HXT48_WN_3.8.0.1111_A04 file. Instead, after some searching, it found drivers from the Chipset_Driver_RKDH5_WN_9.3.2.1010_A01 file, with driver descriptions of:
"Intel(R) C600/X79 series chipset 2-port SATA IDE controller - 1D08"
"Intel(R) C600/X79 series chipset 4-port SATA IDE controller - 1D00"
but none of them worked.
At this stage I cannot install Windows to this SSD.
osprey4
6 Operator
•
34230 Posts
2384
0
Posted December 24th, 2013 02:00
Hi Christos,
As long as you are going to install an SSD anyway, I would set the controller mode to AHCI, perform a fresh installation of the operating system onto the SSD, then set up the HDDs the way you want to.