UNSOLVED

frugal

updated

20 years ago

F

frugal

2 Posts

0

12712

December 30th, 2006 15:00

How can I clean the underside of the 1600n scanner glass?

The underside of my 1600n scanner glass is foggy and is starting to affect the quality of my scans.  How can I clean it?
 
 
The same question was posted in 2003 w/ regard to an inkjet printer.  The Dell moderator responded "The scanner is not really meant to be opened for cleaning; what little dust that accumulates should not cause any problems with the scanners functionality." 
 
I'm really hoping there is a way to clean it.
 
TIA!
  • burrelly

    78 Posts

    809

    0

    Posted January 5th, 2007 21:00

    The scan unit on the 1600 is a sealed unit. Even a field engineer couldent open it to clean it. If there are any problems with the scan glass generally if its not customer damage and the printer is in warrenty dell will replace the whole scan unit.
  • navyman1

    4 Posts

    809

    0

    Posted January 12th, 2007 15:00

    I have the same problem with the foggy appearance on the underside part of the glass on my 1600n printer.  It comes from the moving scanning mechanism smearing a thin coat of grease under it.  It's a design flaw that Dell will not own up to...and unfortunately this foggy appearance doesn't really manifest itself until after your 1 year warranty expires.
  • frugal

    2 Posts

    809

    0

    Posted January 12th, 2007 18:00

    The unit is c. 6 months out of warranty, so Dell isn't going to replace it.  And even if they did, I'd just have the same problem again. 

    Thank you for explaining the origin of the fog.  The unit needs to be designed so that nothing can smudge the glass.  If that is not doable, then it should be designed so the underside of the scanner glass can be cleaned.

     

    I hope Dell is listening.

     

    Message Edited by frugal on 01-12-200702:53 PM

  • wally45

    8 Posts

    809

    0

    Posted February 20th, 2011 12:00

    INSTRUCTIONS FOR CLEANING THE GLASS ON THE DELL 1600n MFP
     
    1. Generally the plastic on the printer needs to come off; unplug all cords; need small phillips head screw driver.
    2. Remove the paper tray and toner cartridge and set to the side out of the way.
    3. Remove the four recessed screws on the back side and remove the panel.
    4. Remove the four recessed screws & four visible screws on the front side. These screws are behind the toner access panel & previously removed paper tray. Four screws each on the left and right sides when looking at it from the front.
    5. Place printer on its right side to remove one screw on the left side panel; the screw is accessed near the back and bottom.
    6. Remove left panel by lifting up on the three tabs that lock on the bottom. The left panel is lifted/tilted from the bottom by the tabs to the top; a little wiggling should break it free. Unplug speaker wire from circuit board.
    7. Place printer on its left side.
    8. Remove right panel by lifting up on the three tabs that lock on the bottom. The right panel is lifted/tilted from the bottom by the tabs to the top; a little wiggling should break it free.
    9. Remove front display panel cover by lifting up on the lip on the front edge. The front display panel cover is lifted/tilted from the front; a little wiggling should break it free.
    10. Remove the three recessed screws on the lower front side of the front display panel.  The front display panel  is lifted/tilted from the front; a little wiggling should break it free.
    11. Remove paper clip panel cover on the far left of the front display panel.
    12. Remove top pivoting cover that sits over scanner. This lifts out on the top rear.
    13. Remove the two screws on the top front side of the glass panel assembly.
    14. Remove the two recessed screws on the top back side of the glass panel assembly.
    15. Lift off the glass panel assembly; use fingers along left and right edges to tilt the assembly up; a little wiggling should break it free.
    16. Clean all the glass surface with a good cloth towel (lint free) and a foaming glass cleaner.
    17. Reverse the order to put back together; take your time and be careful. Good Luck!!