WizardOfBoz2

updated

10 months ago

W

WizardOfBoz2

2 Intern

•

173 Posts

0

2275

August 26th, 2022 19:00

setting bifurcation properly for a dell quad ultraspeed nvme adapter in a T7910

The subject line says it all: what settings are needed to use the dell quad with more than one nvme ssd?

Thanks!

  • Chino de Oro

    11 Legend

    •

    8554 Posts

    •

    47161 Points

    970

    0

    Posted August 30th, 2022 19:00

    As I recall, there is no configuration menu in system BIOS for bifurcation, only the PCIe gen and link speed.  I doubt that the settings was the issue because you could see the drives in Windows.  Try Live CD or unformatted (unallocated) drives.

    If you read some similar posts, you will see the common mistake was the issue, not the hardware problem.  Go over your setup, sometimes we can overlook the very basic things in the process.

  • WizardOfBoz2

    2 Intern

    •

    173 Posts

    1020

    0

    Posted August 27th, 2022 12:00

    This is both a bump and a clarification: What bios settings must be changed for the bifurcation to work.  I have two nvme ssds in my dell ultraspeed quad card, and the drive is recognized by Windows (but not readable as its an ext4 partition) and when I boot to ubuntu, the drive would be readable if the system recognized it, but its not.

     

  • WizardOfBoz2

    2 Intern

    •

    173 Posts

    1007

    0

    Posted August 28th, 2022 08:00

    Another bump.  The question is this: On a T7910, how does one set bifurcation settings so that two nvme ssd drives are accessible in linux?

  • WizardOfBoz2

    2 Intern

    •

    173 Posts

    956

    0

    Posted August 31st, 2022 20:00

    Thanks Chino de Oro.  After noodling around a bit I think i found the issue.  The drive was recognized by Ubuntu but not mounted.  So lsblk to find the device and mount to mount it.

    After that I could access all my files.

     

     

  • infinisean

    1 Rookie

    •

    2 Posts

    0

    0

    Posted January 4th, 2026 09:41

    I'm curious if the nvme bifurcation ability in this workstation is somehow hard-locked to only work with Dell Ultraspeed nvme controllers....   I ask because I have a different brand quad-nvme controller which works fine in my windows desktop (i.e. I can see/access all 4 drives independently), but when I put it in my Dell workstation, only the first nvme drive shows up, the other 3 do not... which is exactly what happens when plugged into a motherboard which does not support bifurcation.
    If the functionality is not hard-coded to only accept dell nvme controllers, what else might be causing the remaining 3/4 drives to not show up?    is this function limited to any specific pci-e ports?

    Thanks in advance

  • infinisean

    1 Rookie

    •

    2 Posts

    0

    0

    Posted January 4th, 2026 09:42

    pci-e* bifurcation ability.... not nvme   :)

  • Chino de Oro

    11 Legend

    •

    8554 Posts

    •

    47161 Points

    0

    0

    Posted January 6th, 2026 08:26

    Re:  I'm curious if the nvme bifurcation ability in this workstation is somehow hard-locked to only work with Dell Ultraspeed nvme controllers....

    I don't think it's hard-locked.  I've tested different brands of adapter, i.e. Asus Hyper V.2 and they worked just fine.  Just make sure that you install it on a PCIe x16 slot.

    You may consider to create a separate thread to gain attention as this closed topic was for bifurcation of Dell Ultra-Speed Quad on a T7910 workstation.