UNSOLVED

i3vi3vi3v

updated

7 months ago

I

i3vi3vi3v

2 Intern

•

81 Posts

•

6 Points

0

3679

June 14th, 2020 11:00

“I210 Gigabit Unprogrammed” on Dell T7910

I've recently noticed that one of the two Ethernet ports on my T7910 is not functional.

  • The Windows Device Manager shows the following device with a missing driver:

Ethernet Controller

Device ID:
PCI\VEN_8086&DEV_1531&SUBSYS_00008086&REV_03
PCI\VEN_8086&DEV_1531&CC_020000

Compatible:
PCI\VEN_8086&DEV_1531&REV_03

  • I've looked at another T7910 PCs and I expect "Intel I210" there (PCI\VEN_8086&DEV_1533&SUBSYS_06191028&REV_03).
  • Googling suggests that "PCI\VEN_8086&DEV_1531" belongs to "I210 Gigabit Unprogrammed". 
  • Intel I210 FAQ explicitly says that "I210-AT–0x1531" is "hardware default, indicating an unprogrammed device".
  • Further googling suggests that "intel gigabit ethernet "unprogrammed"" is almost always related to "I210" (here's one of the results).
  • Some people had been trying to find a driver for "VEN_8086&DEV_1531" e.g. I'm probably not the only one with such an issue. 

 So, my questions are:

  1. why might have this happened?
  2. is it possible that some Dell BIOS update was the cause?
  3. how do I fix this?
  4. is it possible that flashing a newer BIOS update would fix this?

 

  • i3vi3vi3v

    2 Intern

    •

    81 Posts

    •

    6 Points

    1952

    0

    Posted August 27th, 2021 12:00

    Few updates, just to log some findings:

    • The A34 BIOS update did not fix the issue (I previously had A32).
      Before the update, there was some note about the parts of the firmware: current versions and the versions to be installed. I think there was some note about the LOM (Lan on Motherboard) version, and existing was the same as "to be installed" for it.
    • Built-in diagnostics show 2000-0620 error when checking LOM. The only info I found regarding this error is this . Sadly, it actually looks somewhat unrelated. <ADMIN NOTE: Broken link has been removed from this post by Dell>
    • BIOS system info shows valid
           "LOM MAC Address"
      , but the next line is
           "LOM2 MAC Address = {none}"
      . That's probably "as-expected"
    • There's some "EeepromAccessTool (Intel Doc # 572162)" tool (which seem to contain the "EEUPDATE" tool inside) that should be used to flash the firmware and configure the adapter. However, it is not publicly available (here's a forum question about downloading it).
    • I found this interesting post, saying that I210 could actually work without any external flash. However, there's still iNVM and MAC to program. 
    • Here's another thread mentioning the flashless-mode MAC programming  . It mentions "The I210 can be used without an external flash memory with very limited features." but I'm still not sure if it's flashless in T7910. Probably I need to study this further.

    • Still, even those who have eeupdate tool, do run into some flashing issues sometimes. I found a number of threads like this. 
    • Here's another thread mentioning the "eeupdate" tool in context of I210 being in the PCI ID of 0x1531 state. This is for ARM, but it highlights that this might be a not-that-simple process.

    • There's also a another tool - the BootUtil, which is a part of the "Intel® Ethernet Flash Firmware Utility"  that is "related to" I210, which is very easy to download. However, the trick is that the "Adapter_User_Guide.pdf" inside says:

     

     

    BootUtil can only be used to program add-in Intel network adapters. LOM (LAN On Motherboard) network connections cannot be programmed with the UEFI network driver option ROM.

     

     


    Thus, it is not actually applicable.

    • someone posted this, which looks like a basic eeupdate cli interface. It is nice that it also allows to DUMP eeprom, which probably should allow to dump the firmware from a funtional T7910 and flash it on another one... Maybe that would be the most correct way to proceed.
    • Finally, I also found <ADMIN NOTE: Broken link has been removed from this post by Dell> dell article: that mentions "Dell 64BIT BIOS Flash Utility" and got an interesting "/updateLom Updates the LOM if mfgMode +FAMM is set" option.
      Sadly, as far as I understand, "mfgMode " is manufacturing mode, which does not sound applicable. And I found nothing about "+FAMM".

    (edited)

  • mazzinia_

    6 Operator

    •

    1534 Posts

    •

    6405 Points

    1882

    0

    Posted August 27th, 2021 14:00

    What about booting a live usb distro, check with ifconfig the data about the messy lan port, and reconfigure it ?

    ifconfig   << to get a list of lan ports .. the one messed up should not have the mac address. the mac address is  ether aa:bb:cc:dd:ee:ff

    ifconfig lanidmessed down

    ifconfig lanidmessed hw ether 00:xx:yy:zz:kk:ww  << change the letters with numbers of your choice

    ifconfig lanidmessed up

  • mazzinia_

    6 Operator

    •

    1534 Posts

    •

    6405 Points

    1938

    0

    Posted August 28th, 2021 03:00

    I'm reposting this, since it seems my original vanished

    What about booting a live usb distro, check with ifconfig the data about the messy lan port, and reconfigure it ?

    ifconfig   << to get a list of lan ports .. the one messed up should not have the mac address. the mac address is  ether aa:bb:cc:dd:ee:ff

    ifconfig lanidmessed down

    ifconfig lanidmessed hw ether 00:xx:yy:zz:kk:ww  << change the letters with numbers of your choice

    ifconfig lanidmessed up

  • i3vi3vi3v

    2 Intern

    •

    81 Posts

    •

    6 Points

    1917

    0

    Posted August 31st, 2021 15:00

    I've not tried this, but I doubt that MAC is the only missing part. From what I've learned about I210, 0x1531 means completely unconfigured. It is not recognized as a network card, and there's no driver. Thus ifconfig would ignore this adapter, just like it ignores the sound card or "unrecognized devices" one might have in the system. This my opinion is partly based on this discussion.

  • mazzinia_

    6 Operator

    •

    1534 Posts

    •

    6405 Points

    1915

    0

    Posted August 31st, 2021 16:00

    ah, I read. Have you already contacted intel for that programming software ?

    Otherwise you could modify the driver to  handle 1531 as the correct one , and then program the mac from linux

  • i3vi3vi3v

    2 Intern

    •

    81 Posts

    •

    6 Points

    0

    0

    Posted April 30th, 2025 19:20

    Interestingly, I just ran into yet another T7910 with the same problem.

    What about booting a live usb distro, check with ifconfig the data about the messy lan port, and reconfigure it ?

    I've just tried to. The `ifconfig` is simply unable to see the messed-up LAN adapter.

    ah, I read. Have you already contacted intel for that programming software ?

    Nope. Their answers to all the other's similar questions was to just go talk to the PC manufacturer (unless you're a PC manufacturer yourself).

    I've just tried to utilize this "Intel I210 NIC Card Firmware Update Utility" for T7920 (the T7910 is not listed in the "Compatible systems" list). Here's what it said:

    c:\Temp\I210_NVMUpdatePackage_v2_00_Windows (1)\I210\Winx64>nvmupdatew64e.exe
    
    Intel(R) Ethernet NVM Update Tool
    NVMUpdate version 1.37.28.0
    Copyright(C) 2013 - 2021 Intel Corporation.
    
    
    WARNING: To avoid damage to your device, do not stop the update or reboot or power off the system during this update.
    Inventory in progress. Please wait [+.........]
    
    
    Num Description                          Ver.(hex)  DevId S:B    Status
    === ================================== ============ ===== ====== ==============
    01) Intel(R) Ethernet Connection          n/a(n/a)   153A 00:000 Not supported
        I217-LM
    02) Intel(R) I210 Blank NVM Device        n/a(n/a)   1531 00:006 Update not
                                                                     available
    
    
    Tool execution completed with the following status: An error occurred when updating a firmware module.
    Press any key to exit.

    Here's the "nvmupdate.cfg" from there:

    CURRENT FAMILY: 1.0.0
    CONFIG VERSION: 1.14.0
    
    ;DELL Section -------------------------------------------------------------
    
    
    ;**************************************************************************
    ;  Dell_Beaver_Lake_2p00_H30936  ******************************************
    ;**************************************************************************
    BEGIN DEVICE
    DEVICENAME: SPRINGVILLE_EXT
    VENDOR: 8086
    DEVICE: 1533
    NVM IMAGE: Dell_Beaver_Lake_2p00_H30936.bin
    SKIP OROM: FALSE
    EEPID: 800007CA
    EEPROM MAP: i210_Basic_Preservation.txt
    REPLACES: 800005ED 800005FE 8000060D 800006A4
    RESET TYPE: POWER
    END DEVICE
    
    ;**************************************************************************
    ;  Dell_Beaver_Lake_2p00_H62572  ******************************************
    ;**************************************************************************
    BEGIN DEVICE
    DEVICENAME: SPRINGVILLE_EXT
    VENDOR: 8086
    DEVICE: 1533
    NVM IMAGE: Dell_Beaver_Lake_2p00_H62572.bin
    SKIP OROM: FALSE
    EEPID: 800007CB
    EEPROM MAP: i210_Basic_Preservation.txt
    REPLACES: 80000621 800006A5
    RESET TYPE: POWER
    END DEVICE
    

    Maybe, after all, I'll actually replace 1533 with 1531 here and see if it helps. A bit later.

  • i3vi3vi3v

    2 Intern

    •

    81 Posts

    •

    6 Points

    1

    0

    Posted May 1st, 2025 18:14

    The good thing about the dell update tool (mentioned in my previous post) is that it is able to see the i210 adapter, at least. Because the "vanilla" Intel tools are unable to do even that: 

    1. The nvmupdatew64e.exe from I210_NVMUpdatePackage_v2_00_Windows.exe from  "Intel® Ethernet Adapter Complete Driver Pack" version 30.1 (suggested here)  says:
      PS C:\Temp\from_intel\I210_NVMUpdatePackage_v2_00_Windows\I210\Winx64> .\nvmupdatew64e.exe
      
      Intel(R) Ethernet NVM Update Tool
      NVMUpdate version 1.40.5.5
      Copyright(C) 2013 - 2023 Intel Corporation.
      
      
      WARNING: To avoid damage to your device, do not stop the update or reboot or power off the system during this update.
      Inventory in progress. Please wait [+.........]
      
      
      Num Description                          Ver.(hex)  DevId S:B    Status
      === ================================== ============ ===== ====== ==============
      01) Intel(R) Ethernet Connection          N/A(N/A)   153A 00:000 Not supported
          I217-LM
      
      
      Tool execution completed with the following status: Device not found.
      Press any key to exit.​

    2. The Get-IntelNetAdapter command, suggested in NVMUpdateTool-Windows_Rev1.5.pdf  does not see the unconfigured adapter:      
        PS C:\> Import-Module -name "C:\Program Files\Intel\Wired Networking\IntelNetCmdlets\IntelNetCmdlets"
        PS C:\> Get-IntelNetAdapter
      
        Location        Name                                                           ConnectionName            LinkStatus
        --------        ----                                                           --------------            ----------
        0:25:0:0        Intel(R) Ethernet Connection I217-LM                           Ethernet 1                1.00 Gbps ...
             ​
  • Fredrick908

    1 Rookie

    •

    7 Posts

    •

    1 Point

    0

    0

    Posted April 30th, 2026 22:40

    I have the same issue someone please help!  In my dell precision 7910 happened after installing the Quadro RTX 6000 randomly stopped working! 

  • Fredrick908

    1 Rookie

    •

    7 Posts

    •

    1 Point

    0

    0

    Posted April 30th, 2026 23:58

    The Gigabit I210 port stopped working showing up as Ethernet Controller in Device manager with same 1531 unprogrammed state, I tried the EEUPDATE in FreeDOS but that just says unsupported and I found 2 pins in the 7910 to short and potentially that was service mode but it had no name and was 3.3V, though did not give me a "Alert in service mode" thing, I really need the second port as the other PCIE slots are occupied with other things I have leaving only Legacy PCI but that I would not use for ethernet.

    Interestingly it literally happened as soon as I installed the Quadro RTX 6000 at first was confused and after a week of troubleshooting came to the conclusion as listed above by others, and can't believe that others have the same issue though I need a solution. It only shows a solid orange LED, not matter in Win 11 or when booting to Dell Logo, and also the BIOS the NIC 2 is enabled.

    My specs:

    Dual Xeon E5-2696 V4

    64GB Quad Channel ECC RAM

    Quadro RTX 6000

    PCIE to SSD.

    Thank you very much for any help!

  • i3vi3vi3v

    2 Intern

    •

    81 Posts

    •

    6 Points

    0

    0

    Posted May 3rd, 2026 12:59

    It's an interesting idea that this could be associated with a GPU installation somehow (I've played with various GPUs on my T7910 as well, including GTX1080Ti).

    • Might be also associated with Intel vPro activation. Not really sure.
    • But, AFAIR, the issue came with some BIOS update, not after some replacing any hardware. 

    Personally, I gave up. I've seen this issue on at least one more T7910, though.