UNSOLVED

jagauthier

updated

22 years ago

J

jagauthier

1 Rookie

•

12 Posts

0

21013

July 30th, 2004 14:00

Trouble with Veritas and PV132T SNC

Hey all,

 

I've got the device mentioned in the subject.  In fact, I *just* got it.  Today I installed the Veritas SAN SUITE, and it did not find the tape drive.  (All of this is fibre)

So, I read the help, which basically reiterated what this link says:

http://seer.support.veritas.com/docs/267635.htm

"Uncheck the Enable Library" option in the Removal Storage MMC Snap-In. So, I did. I unchecked the box and clicked "Apply", and the box rechecked itself.

So, I've tried a few things, but that box will not be swayed. Any suggestions?

 

Jason

 

  • 294

    0

    Posted July 30th, 2004 15:00

    1.  Does the OS device manager detect the robot and tape drives?

    2.  Have you verified that the devices were configured in the SNC manager software (device mapping, LUN numbering..etc)

    3.  Is the fiber channel adapter driver installed ?  (i.e. Qlogic, Emulex).

    4.  Is the fiiber channel port of the SNC connected to the fiber switch switch or HBA?

  • jagauthier

    1 Rookie

    •

    12 Posts

    294

    0

    Posted July 30th, 2004 17:00

    Richard,

    Thanks for the response.  Let me try and answer your questions.  This level of hardware and Fibre channel is new to me and my company, so I won't claim I know it very well, if at all.

    >1.  Does the OS device manager detect the robot and tape drives?

    Yes! All 9 servers can see the tape drive and have the drivers installed.

    >2.  Have you verified that the devices were configured in the SNC manager software (device mapping, LUN numbering..etc)

    I've setup and used the SNC manager but I haven't done any config. I see the PV132T there, but I don't have any idea what to do with it. 

    >3.  Is the fiber channel adapter driver installed ?  (i.e. Qlogic, Emulex).

    Yes. I helped John Trischler from Dell install all the Qlogic drivers on Monday.

    >4.  Is the fiiber channel port of the SNC connected to the fiber switch switch or HBA?

    I'm not sure I understand the question, but I'll try to describe my setup and hopefully answer at the same time.

    The PV132T uses the Fibre channel to a McData switch. Then I have 9 servers also accessing the McData switch.  I went into the switch config and I created a zone for each tape drive and server combination. Once this was done the servers were able to see the tape drive.

     

  • 294

    0

    Posted July 30th, 2004 18:00

    In the OS device manager, check if the drives are installed in a section called "Other" or "Tape Drives".

    Have you installed the Veritas class drivers?  There is a Veritas program on the hard disk called tapeinst.exe.  Run this program and see if the drives are detected.  Be sure to select the option "Install Veritas drivers for all tape devices". 

     

     

     

     

  • jagauthier

    1 Rookie

    •

    12 Posts

    295

    0

    Posted July 30th, 2004 18:00

    Richard,

     Thanks for the response.  I went back and read my original message and realized that I could have given significant more info.

    The servers all see the tape drive.  When I said "Veritas" doesn't see the drive, I was referring to the Tape Driver installation wizard when you first start the application.  Tapeinst.exe does, affectively, the same thing.

    It doesn't see the device.  When I researched this with Veritas' support pages I found the link I posted about disabling the media from removable storage.  But, my system refuses to let me disable it.

    Maybe that is why Veritas cannot see it? I don't know, just going by their document.

     

    Thanks again.

    Jason

  • 295

    0

    Posted July 30th, 2004 19:00

    You mentioned that the drives were detected by the OS, but is the robot detected.  It is either listed under "Other" or "Medium Changers".  RSM should not be the problem.  Backup Exec creates a log file called adamm.log.  View this log file and see if drives are detected and listed.

    In your fiber channel environment, are you using the storport or scsiport fiber channel driver?  Better yet, what version of the Qlogic driver do you have.?

     

  • jagauthier

    1 Rookie

    •

    12 Posts

    295

    0

    Posted August 2nd, 2004 12:00

    Thanks for the response.  I think you are leading me to my overall problem.

    Here's what my system sees as far as the PV132T.

    http://www.pendulus.org/~jgauthier/sysdev.jpg

    (There is nothing under 'Other', or 'Medium Changers')

    I checked adamm.log, and sure enough nothing is detected.

    http://www.pendulus.org/~jgauthier/adamm.log

     

    Also, the Qlogic drivers are 9.0.0.12.

    Thanks,

     

  • 295

    0

    Posted August 3rd, 2004 00:00

    Backup Exec sees no devices.  It is possible that the 132T SNC is not setup properly.  You will need to use the SNC bridge manager software to verify if the SNC sees the devices.  Also check the SCSI caling on the 132T.

  • jagauthier

    1 Rookie

    •

    12 Posts

    295

    0

    Posted August 4th, 2004 13:00

    Richard,

      Thanks.  That helped isolate the issue.  In my inexperience I did not have the device cabled properly.  So, now I do.  And BE sees the device.  My next issue (Isn't there always a next issue?) Is that the it's coming up as an "uknown drive" and thus being disabled.  I followed Veritas' KB article: http://seer.support.veritas.com/docs/235252.htm.

    It doesn't quite apply.  Do you know what the cause is with this?

    During the Device Wizard:

    In BE's Devices Windows:

     

    One last thing.  In my lack of knowledge (before I even started this thread) I installed the Windows drivers. I tried to uninstall them, but opon the next reboot, they were back. 

  • 295

    0

    Posted August 4th, 2004 15:00

    What you need to do next is tell me what the SNC sees.  Telnet into the SNC and run the following command  "fcShowDevs".  Paste a screen shot and I can view it.

  • jagauthier

    1 Rookie

    •

    12 Posts

    156

    0

    Posted August 4th, 2004 15:00

    SN97T2643404 > fcShowDevs

    Targets Visible to Hosts on FC 1:
    LUN Chan  Id  Lun  Vendor   Product          Rev   SN
    -----------------------------------------------------
      0   0    0    0  DELL     PV-132T-FC       42d4  97T2643404
      1   1    0    0  DELL     PV-132T          227D  DELL1_313434531314
      2   1    1    0  QUANTUM  SDLT320          4646  RBE12Y1246
    value = 2 = 0x2