Molasar

updated

13 years ago

M

Molasar

18 Posts

0

218524

April 23rd, 2014 20:00

LSI20320IE + PV124T (LTO3) + Win2008R2 + PE2950III

Hello,

Does anybody know if this combination works properly? I have read some horror stories about the drive being detected but not the changer, etc.

Are drivers need for the card or does Win2008R2 install them by default?

Is a Dell-branded card needed or does an LSI non-OEM work the same?

Sorry for all the questions!

Thanks!

  • Molasar

    18 Posts

    4271

    1

    Posted June 4th, 2014 20:00

    UPDATE:

    Turns out a shorter SCSI cable arrived today, and I changed cables. Well what do you know? IT NOW WORKS!!!

    W2K8R2 sees the changer (as unknown changer) and BE2010R3 sees the changer now, no problem. Both magazines are enabled and it works like a charm.

    Lesson learned: Be sure to check cables before you start to pull your hair out.

    Thanks to all who chimed in.

  • DELL-Sam L

    Community Manager

    •

    8147 Posts

    •

    34706 Points

    4536

    0

    Posted April 24th, 2014 08:00

    Hello Molasar,

    The PV 124T LTO3 is compatible with the PE2950 and windows 2008R2.  The only issue that I can see is that the LSI 20320IE is not listed that it supports 2008R2 as the last version of windows that it list is 2003 in this link.   www.lsi.com/.../SCG_LSI20320IE_PB_070207.pdf

    The LSI card should work as it does support tape drives and libraries & that card is similar to the card that dell sold as well.  The only issue that I can see is the drivers for the LSI card.  

    If you can get the LSI card to be seen in 2008R2 then you should be able to see the tape drive & medium changer.  If you can’t see the medium changer or tape drive in device manger then what you may have to do is install the enumerators for both the tape drive and medium changer and that should make it so that they both show up in device manger.  

    Please let us know if you have any other questions.

  • Molasar

    18 Posts

    4536

    0

    Posted April 24th, 2014 09:00

    Thanks Sam.

    According to this link:

    www.lsi.com/support/Pages/download-results.aspx?component=Storage+Component&productfamily=Legacy+Host+Bus+Adapters&productcode=P00028&assettype=0&productname=LSI20320IE

    there is a Win2K8 driver for the LSI20320IE. The readme.txt says it includes an x64 StorPort version too. Don't know if it works for Win2K8R2.

    Just two more questions:

    1) What are the emulators and where do I get them?

    2) Since the PV124T LTO3 is compatible with the PE2950III and Win2K8R2 according to your answer, and being that the LSI card "might be the weak link" in this setup, suppose I take the LSI out of the equation. What would be the "ideal" host card (in place of the LSI)?

    As a sidenote, this particular PE2950III has PCI-e ports (which I believe is the standard config).

    Thanks!

  • DELL-Sam L

    Community Manager

    •

    8147 Posts

    •

    34706 Points

    4536

    0

    Posted April 24th, 2014 13:00

    Hello Molasar,

    The enumerators are added in windows under legacy hardware in device manger.  You will need to choose tape drives and add the tape bus & changer bus enumerators that should make it so you can see the medium changer& drive correctly.  

    Well if you were to take out the LSI card & wanted to go with a card that we offered in the system it would be an LSI2032 which is what you currently have.  The big difference is that the Dell LSI card just has a dell firmware on the card where LSI has their own firmware on it.  As long as you install the LSI card with LSI drivers then you should be good in getting the PV124T seen correctly by the server.

    In the PE2950III you should have 2 PCIe slots & as long as you insert the card into one of those slots you should be good.  Also there is no special settings that is needed so if you use the factory settings for the card you should be good as well.  

    Please let us know if you have any other questions.

  • Molasar

    18 Posts

    4546

    0

    Posted May 29th, 2014 22:00

    Well, I finally connected the whole thing and lo and behold, only the drive gets detected. I went into

    legacy hardware, chose tape drive and nothing was there. Just "Have Disk."

    LSI drivers won't install - Windows 2K8R2 responds with "Already have latest driver installed".

    What else can I do?

    In POST, both the loader and the drive are displayed. But once in Windows (Device Manager), only the drive shows up. Tried changing SCSI IDs to no avail.

    Please help!

  • DELL-Sam L

    Community Manager

    •

    8147 Posts

    •

    34706 Points

    4546

    0

    Posted May 30th, 2014 07:00

    Hello Molasar,

    When you boot up the PV124T and the server did you boot the 124T first and wait 10 minutes till it said ready on the front panel before booting the server?  With the PV 124T it has to be at a ready state before the server can be powered on to properly be seen.  If you have waited till the PV124T was at a ready state first before powering on the server does the scsi card bios see both the tape drive and the medium changer?  If both the drive and the changer are seen by the scsi card bios then windows should see the robot & drive.  Sometimes the robot is seen as an unknown medium changer, or medium changer.  

    Please let us know if you have any other questions.

  • DELL-Sam L

    Community Manager

    •

    8147 Posts

    •

    34706 Points

    4546

    0

    Posted May 30th, 2014 08:00

    Hello Molasar,

    If you go into the SCSI card bios & do you have the option to enable multi lun support?  If so then enable it on the channel on the card and save the settings and let the server boot into windows and see if the medium changer shows up.  

    Please let us know if you have any other questions.

  • Molasar

    18 Posts

    4546

    0

    Posted May 30th, 2014 08:00

    Hello, I have indeed waited until the PV124T shows a ready state in the front LCD. Booted up server, and during POST, LSI 20320IE, autoloader and drive are seen; the autoloader and drive are the same SCSI Id, different LUN (0 and 1).

    I searched for it in the Device Manager and found no reference to an unknown medium changer, only the drive itself. I installed latest firmware on both autoloader and drive from the web browser.

    Don't know what else to do, short of buying a Storagetek SN3250 FC / SCSI bridge (FC card is installed in the server)

    Please help!!

  • Molasar

    18 Posts

    4546

    0

    Posted May 30th, 2014 09:00

    Unfortunately, the LSI 20320IE card has an HP bios build on it, and pressing F8 during POST brings up a tiny configuration menu. No multi-LUN option there. So I figured that should be set by default as the POST clearly shows the scsi adapter, drive (IBM) and autoloader.

    No driver or anything on the HP site.

    Strange that Dell management shows the card as a Dell...

    Is it time to search for an LSI 20320IE with a Dell bios and trash the HP one?

    We were looking into getting an ATTO card, but have read forums where people are having the same issue.

    We're seriously looking into the StorageTek SN3250 FC/SCSI bridge...

    One other thing: The Dell configuration website for the PV124T shows the IBM full height LTO3 drive as having hardware compression; Backup Executive shows that hardware compression is disabled. No idea why this is so.

    We have flashed the loader and the drive with the Dell website with no problems. Trying to flash the drive with Dell ITDT shows an error and flash cannot continue. This happens with the exact same flash image (same file).

    The PV124T shows absolutely no problems during boot or within the management website. We ran all sorts of tests and all successful.

    System Event Log shows no hardware errors.

    The PE2950III is running Windows 2008R2, all service packs and updates installed. This server is used for a record label as storage and database server, so we're getting really nervous about our data.

    Any ideas?

  • Molasar

    18 Posts

    4546

    0

    Posted June 1st, 2014 20:00

    Update: I got hold of some firmware images from the LSI site, and successfuly flashed the card. It was quite easy following the LSI instructions. The utility flashed both the ROM and firmware successfuly. Looks like I got a non-OEM LSI card now.

    So the card's HP firmware is gone!

    Pressing Ctrl+C (prompted during POST - it wasn't there with the HP fw), I could now go into the card's BIOS. It has a listing of the SCSI IDs, and within each ID, there is the option of scanning LUNs. That was enabled by default.

    I looked all over the place and found no relevant settings that might be of use here, save the setting above.

    I rebooted the server, and once again, drive, PV124T and card gets displayed on POST.

    Windows 2K8R2 booted, and once again, only the drive is present on the Device Manager.

    I uninstalled the card from Device Manager and rebooted.

    Once booted, Windows searched Windows Update briefly and installed the SCSI card, where once more it prompted me to reboot.

    Did that. Still no joy. Only the drive is present in Device Manager.

    Any clues?