UNSOLVED

Karl327

updated

21 years ago

K

Karl327

14 Posts

0

18502

March 15th, 2006 00:00

Raid Setup PE2400 How to do it?

I got the PE2400 on Ebay and is in good shape.  I did however determine that I needed more disc space so I got the recommended Seagate from Dell (73GB x3).  I wish to install thee of them as a Raid.
 
I thought I understood the process but alas, NOPE.:smileysad:
 
What I have successfully accomplished was to install three drives in th the first three bays. Ran the Dell Installation and Server CD and viola, after going through some steps the first drive is up and running with Windows 2003 SBS; but just drive 2 and 3 are visible through the Administrative tools in W2003SBS.  They are physically recoggnized but not utilized.  This means to me that the RAID in not configured properly.
 
All the firmware was successfully upgraded and worked ont he previous drives.
 
I have not set up a RAID before so I read the instructions from Dell and there is reference to an Array Manager but I cannot find it on  the system. 
 
Can someone direct me to some instructions on how to set up the Raid on PE2400?
 
Thanks
  • dot45

    29 Posts

    329

    0

    Posted March 16th, 2006 05:00

    I assume that you are wanting to make it a striped volume across all the drives (raid 0). you need to press "ctrl+M" while its scanning the perc card during the boot process. then you need to configure the drives to be setup in a logical disk, after that you then install windows. Windows will see the logical volume, it won't know about the raid setup, because it is being done at the hardware level.
  • Karl327

    14 Posts

    329

    0

    Posted March 16th, 2006 10:00

    Thanks to your interprettive skills I have a step to completing this task.

    Unfortunately, I tried what you stated and all that works during boot up are: F2, F10, and Ctrl-A (Scsi controller).

    I tried Ctrl-Mthroughout the boot up and nothing,  What am I missing?

  • dot45

    29 Posts

    329

    0

    Posted March 16th, 2006 14:00

    do you have the raid key and the extra stick of ram installed on the motherboard, or a PERC scsi card? you must at least have the raid key installed in the system to enable the onboard raid features, without that you won't be able to join the drives together.
  • Karl327

    14 Posts

    329

    0

    Posted March 16th, 2006 23:00

    I found won on ebay and will receive it next week.  It was 50 USD with some PC133 memory.  Because of your help I was able to locate a document Activating the Dell PERC 2/Si.  It states not to use the PC133 memory in the controller.  IS THIS GOOD  FOR THE CONTROLLER? It was sold as set and I have little choice.  I could not even find it to buy on Dell's site.  Try the search Raid Hardware Key.  It is bothersome. 

    I could locate on any search in dell.com to find out information.   You have been the greatest :smileyhappy: help in pointing me in the right direction.  Thanks for the time you have spent answering.

  • dot45

    29 Posts

    329

    0

    Posted March 17th, 2006 01:00

    if i remember correctly, the ram could be pc133, but its not quite normal ram though. must be uinbuffered. not registered. but i think that it is still supposed to be ECC. post the auction # and I'll take a look at it.
     
    once its installed then you hit ctrl-M when booting and it opens the raid config, then you just add the drives to a logical disk and exit the configuration and start installing windows.  don't forget to install the raid driver when it asks you F6, windows will see the raid disks as one drive (since the hardware is handling the drives, not windows).
  • Karl327

    14 Posts

    329

    0

    Posted March 17th, 2006 09:00

    About the driver: Should I have it on a floppy before I start the process?

     

    I copied the photo from the auction and pasted it here. The auction number is 5881377234. 

     

     

  • dot45

    29 Posts

    329

    0

    Posted March 17th, 2006 21:00

    yeah, will be out of town till sunday, i'll check the board as soon as i get back though, if you have an AIM screenname, then private message me with it.
  • Karl327

    14 Posts

    329

    0

    Posted March 23rd, 2006 18:00

    I am ready for the next step.  I was wondering if you could recommend a configuration.

    I have a total of 4 73GB SCSI Seagate hard drives.

    My intention is to use three of them in the RAID.  Keep the forth for a backup.  I was going to create a  drive 0 for the operating system and let the remaining excess be for storage etcetera.

    Should I put the other 9 GB in the three vacant slots and string them together? Can it be done and should it be done? The original 6 9 GB. I was going to simply ebay them.  What would you do?

     

  • dot45

    29 Posts

    331

    0

    Posted March 23rd, 2006 22:00

    I would put two of the 9gb drives back in and run them in a raid 1 array, put the OS on them. use the large drives in a raid 0, if you don't care about the data (if you lose a drive with raid 0 then you cannot get the data back), raid 5 allows you to strip data across multiple drives and gives you fault tolerence.
  • dot45

    29 Posts

    388

    0

    Posted March 23rd, 2006 22:00

    i would be like to purchase the 4 other drives that you have left over, or at least the drive trays.