Hello, the “Avago EFI SAS Driver Unhealthy status” error is typically reported when the system detects a problem with the RAID controller or the drives connected to it.
I don't know which server and PERC you have it but below steps for generic steps.
To access the Avago EFI SAS Driver PERC, enter it and look at the information shown. You will be asked to type a letter. Press 'Y' and enter.
To exit the Recovery Mode of the LifeCycle Controller:
-Go to F2 -> System Setup -> iDRAC Settings -> Lifecycle Controller to see the status
-Select: Lifecycle Controller set to Enabled
-Collect System Inventory on Restart set to Enabled.
-Cancel Lifecycle Controller Actions set to Yes.
UEFI0116 usually means a problem with the disk drive.
Perform diagnostics and update drivers and firmware for storage chain: PERC, backplane, hard drives
To perform diagnostics:
Boot to F11 on Dell Splash screen, choose Boot Manager -> System Utilities -> Launch Dell Diagnostics. Record any messages and continue testing."
or Disable and Re-enable the Lifecycle Controller: You can disable and then re-enable the Lifecycle controller through the command line. The commands are as follows:
racadm set LifecycleController.LCAttributes.LifecycleControllerState 0
racadm set LifecycleController.LCAttributes.LifecycleControllerState 1
DELL-Erman O
Social Media and Communities Professional
Dell Technologies | Enterprise Support Services
#IWork4Dell
Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!
RAID Controller in Slot 6: Dell PERC <PERC H730P Adapter> Driver Health Protocol Utility
Critical Message
There are offline or missing virtual drives with preserved cache. Please check the cables and ensure that all drives are present. Press any key to enter the configuration utility.
Enter Your Input Here:
i First you might need to press <Enter> to get the input window. Then press the desired key(s) in response to the critical message displayed above... (Press <F1> for more help)
Please help i am stuck with this message and server is not restarting.
Hello, it could be the hardware issue for you as well just like Marco says. https://dell.to/3POasK9 You can also reach out to the region support for a second opinion and hardware replacement.
Respectfully,
Social Media and Communities Professional
Dell Technologies | Enterprise Support Services
#IWork4Dell
Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!
DELL-Erman O
Moderator
•
2984 Posts
•
14874 Points
0
0
Posted December 12th, 2023 12:05
Hello, the “Avago EFI SAS Driver Unhealthy status” error is typically reported when the system detects a problem with the RAID controller or the drives connected to it.
I don't know which server and PERC you have it but below steps for generic steps.
To access the Avago EFI SAS Driver PERC, enter it and look at the information shown. You will be asked to type a letter. Press 'Y' and enter.
To exit the Recovery Mode of the LifeCycle Controller:
-Go to F2 -> System Setup -> iDRAC Settings -> Lifecycle Controller to see the status
-Select: Lifecycle Controller set to Enabled
-Collect System Inventory on Restart set to Enabled.
-Cancel Lifecycle Controller Actions set to Yes.
UEFI0116 usually means a problem with the disk drive.
Perform diagnostics and update drivers and firmware for storage chain: PERC, backplane, hard drives
To perform diagnostics:
Boot to F11 on Dell Splash screen, choose Boot Manager -> System Utilities -> Launch Dell Diagnostics. Record any messages and continue testing."
or Disable and Re-enable the Lifecycle Controller: You can disable and then re-enable the Lifecycle controller through the command line. The commands are as follows:
DELL-Erman O
Social Media and Communities Professional
Dell Technologies | Enterprise Support Services
#IWork4Dell
Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!