UNSOLVED

jleni

updated

7 years ago

J

jleni

1 Rookie

•

15 Posts

0

5143

September 16th, 2019 10:00

R640 + SAS + NVMe drives

I have an R640 (0JYYR) with 2x SAS 600GB 10K drives. Everything works well. I am using them in a RAID configuration. The controller is a PERC H730P Mini (Embedded) firmware 25.5.5.0005.

I am currently testing a new 980GB Samsung DCT 983 drive (NVMe U.2 drive). I loaded in the front with a Dell caddy and the power lights are on. It seems to be working...

However, the drive is not detect anywhere (iDRAC9, Lifecycle controller, Linux, etc.)

I have tried upgrading all Dell firmware everywhere (except from the NVMe drive) and also have tried AHCP and RAID modes.

Is this a configuration issue? Is it possible to have both SAS and NVMe drives in the same backplane?

Any tips?

  • Daniel My

    12 Elder

    •

    6204 Posts

    3478

    1

    Posted September 16th, 2019 16:00

    Hello

    OJYYR is a chassis sold with a 8x2.5" SAS/SATA backplane. I show that backplane does not support NVMe. I see in the manual(page 134) it is stated that NVMe is supported on the 8 drive backplane. I will submit to have that corrected.

    Thanks

  • jleni

    1 Rookie

    •

    15 Posts

    3461

    0

    Posted September 17th, 2019 06:00

    Hi Daniel,

    Thanks for your prompt response!

    This is a serious mistake because it is what I checked when ordering the hardware!

    So you are indicating that there is no way an NVMe drive is supported in this hardware (even if described in the manual)? Is there any upgrade that could be done in case I want to have NVMe support?

    I am very disappointed about this mistake...

  • jleni

    1 Rookie

    •

    15 Posts

    3456

    0

    Posted September 17th, 2019 07:00

    Ok, I am looking at the manual.

    Assuming that there is a mistake and "2.5 inch (x8) SAS, SATA or NVMe backplane" is incorrect.

    Is there any way I can plug and NVMe drives to R640 (OJYYR) even if that means changing the backplane, adding to the back or anything?

    This mistake is serious as it significantly reduces the upgrade paths for this server model

     

    Btw, are you sure that this is a mistake? It is also the same here:

    https://qrl.dell.com/Files/en-us/html/Manuals/R640/Hard%20drive%20backplane=GUID-2BB31D86-E9BE-41E9-9984-D7ACED071763=1=en-us=.html

     

  • jleni

    1 Rookie

    •

    15 Posts

    2703

    0

    Posted March 15th, 2020 18:00

    HI Daniel,

    Is there any way I can upgrade the backplane to one that supports NVMe?

    Could you please provide more information, ideally a solution?

    Thanks!

  • leadyrob

    2 Posts

    1261

    0

    Posted December 11th, 2020 06:00

    Is it still the case that NVMe drives aren't supported when connected to a PERC controller?

    We've recently purchased a similar setup - R640 with the 8 drive chassis (part number JKFH7), H730P mini PERC controller, 2 x 1.6TB SAS drives and a 1.6TB NVMe drive.

    The two SAS drives can be seen fine, but there's no visibility of the NVMe drive.

    Cheers,

    Rob

  • jleni

    1 Rookie

    •

    15 Posts

    1250

    0

    Posted December 11th, 2020 07:00

    This is was VERY VERY frustrating because the documentation (manual) at the moment we bought the servers indicated that they had NVMe support.

    Support was not very helpful really.. In the end, they acknowledged that there was a mistake.. The servers are not really useful without NVMe support really..

    I asked about changing the backplane without much help really. Dell support is strange and inefficient.. lots of formality (phone calls, requests for logs, etc.) but not clear answers for questions that are well defined.

    I was really disappointed.. 

  • Dell-DylanJ

    6 Operator

    •

    2924 Posts

    1255

    0

    Posted December 11th, 2020 07:00

    Heya Rob,

     

    If you would like to send me your service tag in a private message, I can check the hardware config. The reason I bring it up is that I can check the backplane. Not all backplanes offer NVMe support. It would seem the most logical place to start, to me at least.

     

    Looking at the documentation, this is what I see:

    2.5 inch (x8) SAS, or SATA backplane

    2.5 inch (x10) SAS, SATA, or NVMe backplane

    2.5 inch (x10) SAS, SATA, or NVMe backplane and 2.5 inch (x2) SAS or SATA backplane (back)

    3.5 inch (x4) SAS or SATA backplane

     

    This is why I think this is a good launch point. Based on your description, it likely doesn't offer NVMe support, but I'd like to get the hardware config, just so I don't give you any bad information.

  • grhn

    2 Posts

    1516

    0

    Posted April 21st, 2021 07:00

    I have the same question. We ordered a configuration which has 8x 2.5" backplane, which does not seem to support NVMe drives. Just found it out the hard way as Intel P4610 drive is not recognized (mounted in Dell caddy in front bay).

    I found some used 10x 2.5" NVMe backplanes (PGJ4P) online, is it possible to replace the current backplane with that one?

    We have a second CPU ordered, if that matters.

    Thanks!

  • DELL-Chris H

    7 Practitioner

    •

    9682 Posts

    •

    48046 Points

    1508

    0

    Posted April 21st, 2021 07:00

    Grhn,

     

    There isn't a way to do that, as the backplanes are chassis dependent. Now if you got the server within the last 30 days, I would contact Customer Cares or your sales rep and they may be able to exchange it. 

     

    Let me know if this helps.

     

     

    DELL-Chris H

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell

    Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!

  • grhn

    2 Posts

    992

    0

    Posted April 21st, 2021 08:00

    Thanks for the quick reply. Does this chassis support installing 3x NVMes via PCIe cards?