Dell Wireless 1704 802.11b/g/n (2.4GHz) adapter - refuses to connect to
internet on Dell 15R Inspiron 5220
Hi,
Whenever i boot my machine (sometime from hibernate mode), sometimes WiFi adapter refuses to connect to internet. if i reset WiFi adapter then also it refuses to connect to internet.
the only solution i found is to restart entire OS.
the Dell Wireless 1704 802.11b/g/n (2.4GHz) driver version installed is latest one
Any Idea about this problem?
here is the further detail of problem as by "Windows Network Diagnostic report" :
Diagnostics Information (L2sec Helper Class) Details about L2Sec Helper Class diagnosis: For complete information about this session see the Wireless Diagnostic Informational Event. Helper Class: Layer2 Security Initialize Status: Success Result of diagnosis: Problem found Root cause:Windows cannot connect to "abc" The wireless network security key is not correct. Detailed root cause: Layer 2 security key exchange using user-supplied key did not generate unicast keys before timeout Repair option: Verify the network security key for "abc" View the security settings. You can then type the correct security key. Information for connection being diagnosed Interface GUID: {dc8f7df4-e97d-449f-9300-6531d0fe9589} Interface name: Dell Wireless 1704 802.11b/g/n (2.4GHz) Interface type: Native WiFi Profile: abc SSID: abc SSID length: 5 Connection mode: Infra Security enabled: Yes Connection ID: 6 Security settings provided by hardware manufacturer (IHV): No Profile matches network requirements: Yes Pre-Association and association status: Success Security and Authentication: Configured security type: Wireless Protected Access with pre-shared keys (WPA-PSK) Configured Encryption type: TKIP Security connect status: Fail 0x00048005 Number of security packets received: 0 Number of security packets sent: 0 802.1X protocol: No Key exchange initiated: Yes Unicast keys received: No Multicast keys received: No Network Diagnostics Log File Name: 038F6F44-D458-44BE-B4CD-21B7943C4DE3.Diagnose.0.etl Other Networking Configuration and Logs File Name: NetworkConfiguration.cab Collection information Computer Name: XYZ-PC Windows Version: 6.1 Architecture: amd64 Time: Saturday, October 06, 2012 6:56:20 PM
Before reinstalling the Windows, you may try changing the security type on the wireless network. Please refer to the user manual of your Wireless Router for the same.
Also perform the following steps to change the power settings of the wireless card:
1. Click on Start and type ‘Device Manager’ (without the quotes) in the search box. 2. In the search results above, click on Device Manager. 3. Expand Network Adapters category, right-click the wireless adapter, click ‘Properties’, click ‘Power Management’ tab, and then clear the ‘Allow the computer to turn off this device to save power’ check box.
Also try the power management settings in Windows. The steps are listed below:
1. Click Start > Control Panel > Power Options > Edit Plan Settings. 2. Click on Advanced Settings. 3. Expand ‘Wireless Adapter Settings’. 4. Expand ‘Power Saving Mode’ and select ‘Maximum Performance’.
5. Click on Apply and OK.
Let me know if you need further information or assistance.
Did you try changing the security type? You may try changing the encryption type on the wireless network from WPA-PSK to WEP and see if that helps. If that does not resolve the issue, you might have to reinstall the operating system.
Please remember to backup the data before re-installing the Windows.
Let me know if you need further information or assistance. I will be glad to help.
Start, control panel, device manager. Click on Network and then right click on your wireless adapter, left click properties, power management. Uncheck the box, allow computer to turn off this device to save power.
Click on advanced and look and see if this adpter has antenna diversity. If it does, then change the antenna diversity from Auto to Aux.
Go to the power options, and changed the Wireless Adapter Setting, from Maximum Power Setting to Maximum Performance.
As mentioned in Intel ( http://www.intel.com/support/wireless/sb/CS-030709.htm ) configuration....I used Channel bonding/Mixed mode, to make the adapter to use 20/40MHz instead of 20MHz only(default).
And Voila!! ...It Worked for me...now it is not causing any problem. (all the other configuration are mentioned in this thread)
I cannot believe that Dell has done nothing about this issue. I just had gone through the whole set up for my router and other things just to find that it is Dell that is causing the issue and not anything else. Should have thought of this earlier. People from Dell keep suggesting to try and change this on the router try to change that, but the issue is that Dell is the new introduction to the system that was working fine. I have other laptops that connect at good and relaiable speeds but it is this stupid machine that has caused all the grief.
The above tips and the tips from en.community.dell.com/.../19466262.aspx seem to work but still my ping back to the router is taking much more time than the Toshiba, HP sitting right next to it. OK I have swapped positions and places in the room but unless I am sitting in the same room as the router the thing does not seem to work as better as others. The only issue with max WiFi power setting is that it will chew more power so really we should nto have to do it. I also think that the physical position of the WIFI card in the laptop could be an issue as well. I say this as changing the way the laptop faces seem to improve things. I have done more trouble shooting with this machine than I have ever done in my life with any thing that I have bought from any other manufacturer.
Look since I posted this I have had to do more setting changes on the adapter. Basically I have told the adapter exactly what each parameter for the link is and it seems to be okish, still drops but nothing like before. But still the service is unacceptable.
Another update, there is something in the adapter that everytime you change a setting it resets itself and seems to be fine for few seconds and then goes back to drop outs. Still investigating but my gut feeling is the physical position or other internal intereference to the adapter. Could be and happy to be wrong here.
The signal strength indicator is all over the place. Have never seen this before.
DELL-Gaurav Sh1
164 Posts
8736
0
Posted October 7th, 2012 05:00
Hi viber,
Before reinstalling the Windows, you may try changing the security type on the wireless network. Please refer to the user manual of your Wireless Router for the same.
Also perform the following steps to change the power settings of the wireless card:
1. Click on Start and type ‘Device Manager’ (without the quotes) in the search box.
2. In the search results above, click on Device Manager.
3. Expand Network Adapters category, right-click the wireless adapter, click ‘Properties’, click ‘Power Management’ tab, and then clear the ‘Allow the computer to turn off this device to save power’ check box.
Also try the power management settings in Windows. The steps are listed below:
1. Click Start > Control Panel > Power Options > Edit Plan Settings.
2. Click on Advanced Settings.
3. Expand ‘Wireless Adapter Settings’.
4. Expand ‘Power Saving Mode’ and select ‘Maximum Performance’.
5. Click on Apply and OK.
Let me know if you need further information or assistance.