UNSOLVED

cividan

updated

7 years ago

C

cividan

1 Rookie

•

16 Posts

0

1003409

November 1st, 2012 13:00

Dell 6248 Find port of IP address

Hi, I use a Dell 6248 switch and I want to switch vlan of a particular device but I don't know on which port this device is connected. How can I find this information without having to physically go to the switch.

I don't know if it matter or not but the dell switch is not the master switch doing the routing.

  • cividan

    1 Rookie

    •

    16 Posts

    32513

    0

    Posted November 1st, 2012 15:00

    Ok and how do I associate the mac-address to an IP address ?

  • cividan

    1 Rookie

    •

    16 Posts

    32513

    0

    Posted November 2nd, 2012 05:00

    Thanks for the tip but my device is not a computer so this doesn't really help, I will repeat my question: How can I find which port correspond to a specific IP address ?

  • cividan

    1 Rookie

    •

    16 Posts

    32514

    0

    Posted November 2nd, 2012 06:00

    Hi, this is what is returned from this command, I don't know if I should enable or disable something in this configuration to have IP address returned.

    Dell6248#show ip arp inspection

    Source MAC Validation.......................... Disabled

    Destination MAC Validation..................... Disabled

    IP Address Validation.......................... Enabled

    VLAN  Configuration Log Invalid           ACL Name                Static flag

    ----  ------------- ----------- --------------------------------  -----------

      1       Disabled     Enabled

     10       Disabled     Enabled

     20       Disabled     Enabled

     30       Disabled     Enabled

     40       Disabled     Enabled

     50       Disabled     Enabled

     70       Disabled     Enabled

    145       Disabled     Enabled

    180       Disabled     Enabled

    Dell6248#

    *********

    On my cisco SGE-2010 switch I can issue this command to get the port of an ip address and I was hoping to get someting like that on the Dell switch:

    Cisco-SGE2010# show arp ip-address 10.10.20.1

    ARP timeout: 60000 Seconds

     VLAN    Interface     IP address        HW address          status

    --------------------- --------------- ------------------- ---------------

    vlan 20                    10.10.20.1      00:26:f2:b8:8b:32     dynamic

  • cividan

    1 Rookie

    •

    16 Posts

    32514

    0

    Posted November 2nd, 2012 11:00

    Hi, here is the result of the show arp, problem is that I see only IP in vlan 20 and not on other vlan... and the one I need to find are on vlan 10...

    Dell6248>enable

    Dell6248#show arp

    Age Time (seconds)............................. 1200

    Response Time (seconds)........................ 1

    Retries........................................ 4

    Cache Size..................................... 1024

    Dynamic Renew Mode ............................ Disable

    Total Entry Count Current / Peak .............. 3 / 4

    Static Entry Count Configured / Active / Max .. 0 / 0 / 64

     IP Address        MAC Address      Interface        Type        Age

    ---------------  -----------------  --------------  --------  -----------

    10.10.20.1     0026.F2B8.8B32     vlan 20         Dynamic    0h  0m 11s

    10.10.20.2     5C26.0AC0.109C     vlan 20         Local         n/a

    10.10.20.56    6C62.6D05.FF2E     vlan 20         Dynamic    0h  0m 14s

    Dell6248#

  • cividan

    1 Rookie

    •

    16 Posts

    4674

    0

    Posted November 2nd, 2012 12:00

    I tried that already but since the swith as only 1 IP address for vlan20 it can't ping the vlan 10 IP that are located on other port on that same switch...

  • cividan

    1 Rookie

    •

    16 Posts

    4800

    0

    Posted November 5th, 2012 10:00

    Hi, result from the show arp switch command:

    Dell6248>enable

    Dell6248#show arp switch

       MAC Address        IP Address     Interface

    ------------------- ---------------- ------------

    when I try to ping the address:

    Dell6248#ping 10.10.10.10

    Pinging 10.10.10.10 with 0 bytes of data:

    Reply From 10.10.2.2: Destination Unreachable.

    Reply From 10.10.2.2: Destination Unreachable.

    Reply From 10.10.2.2: Destination Unreachable.

    Reply From 10.10.2.2: Destination Unreachable.

    ----10.10.10.10 PING statistics----

    4 packets transmitted, 0 packets received, 100% packet loss

    round-trip (msec) min/avg/max = <10/<10/<10

    Address: 10.10.2.2 is the default vlan ip address of the switch

    The ip is valid and I can ping it from my computer no problem but not from within the switch.

    C:\>ping 10.10.10.10

    Envoi d'une requête 'Ping'  10.10.10.10 avec 32 octets de données :

    Réponse de 10.10.10.10 : octets=32 temps<1ms TTL=127

    Réponse de 10.10.10.10 : octets=32 temps<1ms TTL=127

    Réponse de 10.10.10.10 : octets=32 temps<1ms TTL=127

    Réponse de 10.10.10.10 : octets=32 temps<1ms TTL=127

    Statistiques Ping pour 10.10.10.10:

       Paquets : envoyés = 4, reçus = 4, perdus = 0 (perte 0%),

    Durée approximative des boucles en millisecondes :

       Minimum = 0ms, Maximum = 0ms, Moyenne = 0ms

  • cividan

    1 Rookie

    •

    16 Posts

    4800

    0

    Posted November 5th, 2012 12:00

    Thanks for trying. maybe someone else will have some suggestion.

  • 4800

    0

    Posted April 2nd, 2013 11:00

    Connect to the IP address of the switch through an ssh or telnet client, like Putty. You'll be prompted for your username and password. Once your in, type "show bridge address-table" to see the mac address table of the switch. I'm not 100% certain that the port numbers are correct, however. I'm still trying to figure out how to refresh the data.

    Also, you can connect to the console through your web browser. Once you're in, navigate to Switch>Address Tables>Dynamic Address Table to view the MAC address to port table.

  • shawn_b1

    15 Posts

    4800

    0

    Posted April 9th, 2014 16:00

    I know this is an old thread, but has anyone been able to do this? Do the PCT6248's have an arp table that is visible to a user?
  • cividan

    1 Rookie

    •

    16 Posts

    4800

    0

    Posted April 10th, 2014 07:00

    Hi, I left the company that had that switch in january 2013 so I was not able to test  the last reply before yours but nothing before that worked.