UNSOLVED

dev_dutta

updated

12 years ago

D

dev_dutta

1 Rookie

•

51 Posts

0

3352

April 30th, 2015 21:00

SAP backup Groups configured through Split mirror Option are getting into hang state after upgrading Networker server from Solaris10 to Solaris11.Index & bootstrap are not getting updated due to which the Group remains in running mode.

SAP backup Groups configured through Split mirror Option are getting into hang state after upgrading Networker server from Solaris10 to Solaris11.

Index & bootstrap are not getting updated due to which the Group remains in running mode.

  • dev_dutta

    1 Rookie

    •

    51 Posts

    1993

    0

    Posted April 30th, 2015 23:00

    Hi,

    Backups confgured through other Storage Node(Old one) work fine but from new Networker server it doesn't work.

    After successful backup it doesn't write index & bootstrap.

  • bingo.1

    1 Rookie

    •

    2430 Posts

    1993

    0

    Posted April 30th, 2015 23:00

    If anything else works fine, I suspect a problem with the appropriate device (not available) or an unmounted volume.

    Keep in mind that NW does not install device drivers, just jukebox drivers.

    "inquire" is the command to verify the known device names.

    However, in this case, you should see a "Media Waiting" alert as long as an appropriate media is not mounted.

    If the volume is on a disk, unmount and remount it carefully - do NOT accidentally re-label it.

  • bingo.1

    1 Rookie

    •

    2430 Posts

    1993

    0

    Posted May 2nd, 2015 09:00

    What I said ...

    Remember that INDEX backups can be directed to a device at a remote storage node.

    BOOTSTRAPS however must be stored as a local device at the NW server.

  • ble1

    6 Operator

    •

    14354 Posts

    •

    56186 Points

    1993

    0

    Posted May 2nd, 2015 14:00

    - what kind of upgrade (from what to what)?

    - what error/pending messages?

  • dev_dutta

    1 Rookie

    •

    51 Posts

    1993

    0

    Posted May 2nd, 2015 22:00

    Hi,

    As I’ve mentioned that the Index & bootstrap is not getting written or updated after each SAP database backups which are of off host/split mirror backup.

    It was working earlier but didn’t work after Master server(Networker server) hardware was replaced with new Operating System was changed to Solaris-11 from Solaris-10.

    NOTE- Index for other similar backups are getting updated from Storage Node -1 which is unchanged.

    Thanks

  • dev_dutta

    1 Rookie

    •

    51 Posts

    1994

    0

    Posted May 2nd, 2015 22:00

    It's a hardware & OS upgrade of Master/Networker server.

    OS Old  One- Solaris-10

    OS New - Solaris-11

    Similar backups from an existing SN is OK.

  • dev_dutta

    1 Rookie

    •

    51 Posts

    1994

    0

    Posted May 3rd, 2015 01:00

    Hi

    As I've mentioned Index & Bootstrap doesn't work for offhost backup configured for SAP database backup.

    Group goes to hang state in Networker level seen through /nsr/applogs ( it doesn't end)

    Normal client backup is ok.

  • bingo.1

    1 Rookie

    •

    2430 Posts

    1994

    0

    Posted May 3rd, 2015 01:00

    The index update is beeing created while the backup runs (except for NMDP). The info is extracted from the save stream.

    Index and bootstrap backups are server related issues. Exclusively. They do not have anything to to with the client data backup at all. That's why it is obvious that it is not SAP related. I am pretty sure that if you configure a 'standard' backup of the NW server client (see below) it will also not work.

    However, 'does not work' and 'worked before' are not really helpful without any further feedback and error messages. (Remote) control without any feedback can just make assumptions. Worst case, look at /nsr/logs/daemon.raw

    Let me suggest that you

      - create a new group

      - add the NW server's client name only

      - specify the save set to a minimum size (/etc) as mentioned.

      - run "savegrp -l full -G " or "savegrp -O -G " and check the output.

      - While running the group, check the NW server for alerts (use the admin GUI or nsrwatch).

  • dev_dutta

    1 Rookie

    •

    51 Posts

    1934

    0

    Posted May 3rd, 2015 06:00

    In case 2- We also installed Solaris-11

    From: Devdutta Mohanty (WI01 - GIS - ENU)

    Sent: Sunday, May 3, 2015 6:55 PM

    To: 'jive-735985249-6ujy-2-iwz6@emc-ecn.hosted.jivesoftware.com'

    Subject: RE: - SAP backup Groups configured through Split mirror Option are getting into hang state after upgrading Networker server from Solaris10 to Solaris11.Index & bootstrap are not getting updated due to which the Group remains i...

    Hi,

    We did below things –

    Case-1- Carried out OS Kernel patch update in Solaris-10(Old Networker server). No changes to NSR installation.

    Case-2- Replaced the Old Networker server/hardware as it’s out of hardware support. Here we copied old “res,mm & Index”.

    In both scenario problem is same.

  • dev_dutta

    1 Rookie

    •

    51 Posts

    1934

    0

    Posted May 3rd, 2015 06:00

    Hi,

    We did below things –

    Case-1- Carried out OS Kernel patch update in Solaris-10(Old Networker server). No changes to NSR installation.

    Case-2- Replaced the Old Networker server/hardware as it’s out of hardware support. Here we copied old “res,mm & Index”.

    In both scenario problem is same.