
UNSOLVED
XPS 15-L521X - How to separate LCD panel from aluminum lid
The video cable between the motherboard and the LCD panel on my XPS 15-L521X has broken and I am trying to replace it. I have the complete lid assembly removed from the body of the laptop but I need help separating the LCD panel itself from the aluminum lid in order to reach the video connector on the back of the panel. Unlike most laptops that have a plastic front bezel over the outer edges of the screen (usually held in place by one screw at each corner), this one has no such bezel. I do understand that there is a pane of Corning Gorilla Glass over the screen. This glass seems to be held in place with a rubber or silicone gasket. I suspect that the glass is just held into place by this gasket but I am very leery about just prying it out. Does anyone know the correct procedure for removing this (as I assume that it is the only way to get at the video connector on the back of the LCD panel)? Thanks in advance,
Responses (11)
Solutions (0)
Thanks EJN63 for the quick reply. There seems to be a rubber or silicone gasket between the glass and the aluminum lid. Should I pry the gasket up with the glass (prying in between the gasket and the lid) or should I pry up the glass alone (prying in between the gasket and the glass)?
First thing to realize is that these are not designed to be disassembled - the chances that the glass panel will survive your attempt aren't high. You very likely will end up needing to replace the entire assembly.
The glass is bonded to the bezel/cover assembly. You will need some way to warm up the edges in order to even begin removing the glass cover. Even then, the slightest torque applied to the glass will likely crack the touchscreen. Proceed with extreme caution for your own safety - gorilla glass is very scratch resistant but it is far from shatterproof -- and it is under tension, so it takes very little torque to crack it.
All in all, you may be better off taking the system to a shop that can repair the cable -- the cost of a replacement display assembly is about $300 and what you're going to try to do will likely end up with you needing a replacement for it.
You can try parts-people.com, but the touchscreen assembly isn't designed to be disassembled - but rather replaced as a unit., so the separate part may not be available.
Is the video cable clearly damaged between where it exits the frame and connects to the mainboard? If it's not, what makes you think it's the cable that's bad?
More and more notebooks are being designed this way - Apple started doing it this way a while ago, and most of the PC companies followed with their touchscreen systems.
Well, through very careful work with a hairdryer, several plastic prying tools and a multitude of toothpicks, I've managed to separate the top layer of glass from the lid. This is quite a different setup from traditional laptops. I believe (hope) that the defective part is the video cable. Try as I might, however, I can't seem to find a replacement online. Can anyone point me in the right direction?
Thanks again, ejn63 for your continued advice. To understand why I think the video cable is the culprit, you need a bit more info. I just bought this computer used (for a good price, I might add). The original owner told me that the laptop had been dropped from a table. The fall dislodged the small silver hinge cover that covers the video cable. At that point, he started having intermittent video problems but was able to get the LCD panel to work by jiggling the exposed video cable. With time, the LCD panel stopped working altogether but he was still able to use an external monitor connected to the HDMI port. When I bought the computer, it was no longer working and gave a beep code of 8 beeps which indicates an LCD fault. When I got the laptop home, I separated the lid from the body of the laptop and was able to get rid of the beep codes and have the laptop boot and display on an external monitor by, again, jiggling the video cable at the monitor end. I also noticed that there was a problem at the video cable where it connects to the motherboard. At that connector, mixed in with the various coloured wires, there are four bare wires that are soldered to two points on the body of the connector. Two of these wires had come apart and had fallen away from the connector. I got out my trusty soldering iron and soldered them back to the connector hoping that this was the source of the fault. It does not seem to have been. My next idea was to separate the screen from the lid to have a better way of securing the video cable to the connector on the back of the LCD. I got this done yesterday but it does not seem to have fixed the problem as the LCD still does not display anything. I have also looked at the backlight ribbon cable to make sure that it was securely connected. It seems to be. As one would try on a CCFL monitor, I shone a light through the screen to see if an image was being displayed without backlighting. It does not seem to be the case as I see no movement with both displays cloned and a video playing. The video control panel detects the internal display and allows me to adjust its resolultion, etc. So why do I think the cable is the culprit? The simple answer is that that seems to be the cheapest part to replace. This comes from my days as a shadetree mechanic working on '60's and 70's Fords: if the battery wasn't charging, you would change the voltage regulator before changing the battery or alternator; likewise, if the car wouldn't turn over, you would swap out the solenoid before the starter. While this may not be the most technically astute approach, it seems to make more economical sense. I may indeed wind up buying the entire top lid assembly (which I have seen at Amazon for $299 US). In the meantime, though, I will muddle along as best I can (helped by the advice of people such as yourself). By the way, this laptop is not a touchscreen model.
Thanks again.
I am really interested to hear how the process went in more detail if possible. I am having a problem with several dust particles (about 1-2mm diameter) in behind the glass, and I would like to remove them. I am afraid that in attempting to separate the glass from the lcd that it will break. Anyway if you can give me some tips on exactly what you did that would be much appreciated! Also, when using a heat gun, isn't there a risk that the head will damage the screen? If anyone can provide me some help it would greatly appreciated!
Thanks in advance!
John
Hi JCOWLE86,
i have to tell you that this is not for the faint of heart, especially after the warnings of a previous poster. The whole process took me about an hour with a hair dryer (and not a heat gun which I thought might have been too hot). I used the dryer to heat up the perimeter of the screen starting with the gap at the bottom where the video cable goes to the screen. I was very careful not to touch the glass with the hair dryer. I had previously bought a laptop tool kit which included several plastic prying tools. These came in very handy. So I started at the bottom, heating up the perimeter and GENTLY prying up with the plastic tools. When an area had come away from the housing, I placed cocktail style toothpicks (the round ones and not the flat ones) between the glass and the housing to keep them apart. I slowly worked my way around. On several occasions, I could see the glass bowing a bit and half expected to hear a cracking sound and to see my Gorilla glass shatter into a million pieces... but that didn't happen. So I finally got the glass off and saw that there are several layers of what seems to be white plastic sheets under the glass. I was also able to gain easy access to the video cable connection which I was able to re-seat but with no success in re-animating the LCD panel. As I said in a previous post, I suspect (hope?) that the ultimate culprit is the cable. I have ordered a used lid assembly including the video cable through eBay from an outfit in Texas. When that comes in, I will try reassembling the screen to see if it works. One area of concern is that there is what seems to be a length of string that sits in a channel on the lid portion of the assembly. I am hoping that this serves the same purpose that windshield installers use and that it serves no electronic function. Also, I still don't know if I screwed something up with the screen and am just not aware of it yet. We shall see.
For your problem: a few specks of dust, I would suggest that the potential risks outweigh the potential rewards. If I were you, I would just learn to live with the dust. If you undertake this disassembly, you may very well wind up with a busted screen which will cost you $300 US plus shipping.
I hope this can help you,
Richard in Ontario, Canada
Hey Richard,
Thanks so much for the quick reply. Yeah that sounds like quite the involved process. It sounds similar to the way they make cell phones. It looks great, but not exactly friendly when it comes to repairs. Anyway I think I might take your advice and just leave it. The dust is not that distracting, and I ended up getting a really good deal on the computer (xps 15 521x) for $440. I'm in Toronto, so that's not US prices either. Anyway thanks again for the info, and best of luck getting yours all fixed up.
Cheers,
John

ejn63
11 Legend
•
87469 Posts
•
321256 Points
4001
0
Posted November 7th, 2014 10:00
It is mounted with adhesive. You'll want to warm up the edges using a heat gun or hair dryer (will take a while) and gently pry the screen away with a plastic scribe. Or, ifixit has their i-opener which you use with a microwave to provide the heat necessary to soften the adhesive.