UNSOLVED

razorjack

updated

22 years ago

Closed

R

razorjack

31 Posts

0

13515

September 19th, 2003 05:00

USB Ports on a 8600 not High Speed?

I connected my USB Scanner (HP Scanjet 5500c) to my brand new 8600 today and XP says that I have a "high speed device connected to a low speed hub".  What gives?  I thought that this laptop had all the latest goodness in it?  Are the USB ports not USB 2.0?

 

/gulp

  • zxcvb531

    103 Posts

    352

    0

    Posted September 19th, 2003 05:00

    Suppose to be USB 2.0
  • razorjack

    31 Posts

    352

    0

    Posted September 19th, 2003 05:00

    Need to check my BIOS settings - maybe it's that legacy USB setting - we'll see
  • starstreak

    84 Posts

    352

    0

    Posted September 19th, 2003 07:00

    high speed worked ok for mine.  I transfered 125mb from a 2.0 usb key in about 15seconds.  and thats quick
  • KeeperC

    11 Posts

    357

    0

    Posted September 19th, 2003 13:00



    @razorjack wrote:

    I connected my USB Scanner (HP Scanjet 5500c) to my brand new 8600 today and XP says that I have a "high speed device connected to a low speed hub".  What gives?  I thought that this laptop had all the latest goodness in it?  Are the USB ports not USB 2.0?

     

    /gulp




    Is the scanner self powered or does it rely on the USB port for power? If USB powered, it may not be getting enough juice from the computer - Dells apparently can't deliver the USB spec current.

    See here http://delltalk.us.dell.com/supportforums/board/message?board.id=insp_general&message.id=129302 and here http://delltalk.us.dell.com/supportforums/board/message?board.id=latit_periph&message.id=442 for related threads.

     

    Message Edited by KeeperC on 09-19-2003 04:10 PM

    Message Edited by KeeperC on 09-19-2003 04:18 PM

  • StuartV

    1 Rookie

    •

    55 Posts

    352

    0

    Posted September 19th, 2003 13:00

    Don't forget that, if you have a USB 1.x device hooked up to any port on a USB root hub controller, ALL USB devices hooked to ports on that root hub controller will be forced to run at USB 1.x speed. Usually, I think a USB root hub controller will have 2 USB ports. So, maybe your problem is you have a USB mouse or something like that hooked to another USB port on your laptop and that is slowing both ports down?

     

    - Stu

  • itzme

    17 Posts

    357

    0

    Posted September 19th, 2003 13:00

    Did you do a clean install of xp, thats my guess this message comes up when the xp drivers for usb arent installed and you need service pack 1 installed on xp to use usb 2.

     

  • razorjack

    31 Posts

    357

    0

    Posted September 19th, 2003 14:00

    This is strange - it's the only device on the bus. I'm wondering if the cable I'm using might be the issue.
  • itzme

    17 Posts

    357

    0

    Posted September 19th, 2003 14:00

    Just some questions that could help us find the problem

    1) Did you do a fresh install of XP after you received the system

    2) In System Properties (right click on "My Computer" and choose properties) does it say service pack 1

    3) are you sure that you're printer is USB 2? How old is it

  • Verns600m

    130 Posts

    357

    0

    Posted September 20th, 2003 16:00

    yes, try to use a usb 2.0 certified cable.

    or maybe you may have to update the chipset drivers for your 8600?

  • razorjack

    31 Posts

    182

    0

    Posted September 20th, 2003 16:00

    Seems that one of the buses wasn't installed properly - was a ? in Device Manager - I then reinstalled the chipset drivers (I think) and it resolved. Now need to reconnect it to the scanner and test.