UNSOLVED

edwenger

updated

21 years ago

Closed

E

edwenger

6 Posts

0

8591

March 1st, 2006 15:00

Inspiron 6000 runs slow - varied GHz in System Properties

PM 1.86 GHz
512 mb Ram
9 cell battery
Intel Pro 2200 Wireless
40gb HD
ATI 64mb video

I bought about 1-2 months ago.

If you open the system properties (right click on My Computer) at the bottom right it tells you what Processor and GHz you have. Then, the line right under that shows your GHz again, along with your RAM. I'm familiar with that, I've seen it many times.

I noticed very soon after I got the computer that the second GHz would change. Quite frequently it was 700+ MHz. I tinkered with the power schemes and that seemed to control it somewhat. So I thought less GHz = less power usage. OK.

Now, even when I have the computer sitting on my desk, plugged into the AC adapter and running on AC power with the battery fully charged and the power scheme set to MAX PERFORMANCE I often only get 300+ MHz. That is SLOW and I can definately tell the difference. And I don't like it.

WHY IS THIS?? Why even when power settings are as high as I can put them is this still doing this? Is it even related to power settings?

I'm about to buy another 6000 for a friend but I want this figured out first.

Thanks,
Eric
  • phil404

    63 Posts

    183

    0

    Posted March 1st, 2006 23:00

    Hopefully, some guru around here will jump in and correct me if I'm wrong, but I believe the Enhanced Speedstep of the Pentium M chips throttles the CPU depending on the needs of the running application(s), and not necessarily as a function of power source (AC vs. batt) alone. Therefore, if you were to stress the machine with a CPU intensive app, I'm pretty sure the CPU would throttle-up to max performance. I just got a 6000, myself, and will do some tests of my own. I'll report back with the results (don't be expecting any fancy graphs or pie charts, heh).
     
    -phil

    Message Edited by phil404 on 03-01-2006 09:00 PM

  • tbsteph

    51 Posts

    183

    0

    Posted March 2nd, 2006 02:00

    You are correct, the power source does not impact dynamic switching. 
     
    Below is a link to a small program that runs in your system tray called Notebook Hardware Control.  If you leave it set to dynamic switching, you can see when the processor speed changes depending on the need.  You can also set the processor to run at top speed all the time.  Personally I see no benefit to have it run full bore all the time but each to there own.
     
    Good luck!
     
     
     
  • edwenger

    6 Posts

    183

    0

    Posted March 3rd, 2006 11:00

    It may be supposed to speed up but it seems to me that it slows down sometimes. If I open Photoshop and QuarkXpress and do a big photo conversion that is about as hard as I can tax the system it will not power up. One of the reasons that I noticed the whole issue is because it seemed so SLOW when I was working on a Quark file. That doesn't sound like speeding up to me. And while earlier I thought it would up the reading when I changed the power scheme it doesn't seem to anymore.

    Now, some other food for thought. I had disabled my wireless card and network connection because I got tired of looking at them at the bottom of the screen with a red X on them and popping up messages and I thought I would conserve any battery that may be used to run them. So I thought just MAYBE that would make a difference. So, I enabled them again and now it works closer to how it did originally. When I set to MAX PERFORMANCE, I have finally seen 1.86 in the second reading--THANKS (I didn't see that for a while)!! And if I set to MAX BATTERY, then it is down to 797 MHz.

    Hmmm......