Albretch Mueller

updated

15 years ago

0

77442

October 13th, 2011 14:00

trying to make an Optiplex 210L boot up from the DVD drive ...

I am a teacher using an old Optiplex 210L at my school which I need to boot up from a DVD drive (live DVD kind of thing)

So, I did install the DVD drive and took care of the jumpers, the CD-ROM drive is the master (in order not to mess with the school property when I take my DVD  out) and the DVD as cable select. I can see the DVD there in the BIOS, from Windows and a live CD

As the box boots I hit F12 but I see no option to boot from a DVD drive. This is all I see

Boot Device Menu

 * Onboard or USB Floppy drive

 * Onboard SATA Hard Drive

 * Onboard or USB CD-ROM Drive

 I thought that using the latest BIOS update would fix this, but it didn't

 How can I make an Optiplex 210L boot from a DVD drive?

 thanks

 lbrtchx

  • speedstep

    11 Legend

    •

    46969 Posts

    838

    1

    Posted October 14th, 2011 05:00

    The DVD Drives on a 210L would be Very old and not necessarily read any media other than DVD -R  and only if Burned at 1X or 2X Speed Max.   I would try a Live CD instead to see if the drive is working.  Otherwise I would suggest getting a newer DUAL Layer compatable PATA DVD drive and installing after setting the drive to CABLE Select.  These models use the old 40 wire Grey Cables.  Newer IDE cables use 80 wires and are color coded.

    The Ends go only to a specific place.   Newer cables make that easier by making the motherboard side Blue, the Master or primary drive Black and the Slave or secondary drive Grey.  ALL Drives are jumpered to CABLE SELECT both Optical and Hard Drives.  80 wire cables are recommended but not usually included on older models.  With much newer models 80 wire cables are required due to the DMA Speed of the pata bus.

  • jackshack

    6447 Posts

    838

    0

    Posted October 13th, 2011 16:00

    The Optiplex 210L uses PATA IDE for the optical drives as I'm sure you know if you have opened the case.  A Dell typically allows you to boot only from the master drive on an IDE channel.  If you are familiar with the System Setup page for the BIOS you can try a trick to get your DVD to boot; start the computer, press F2 for the System Setup page while the Dell logo can be seen on the display.  Navigate to the menu for the IDE channel and turn the port for IDE drive 0 to Off.  Navigate to the boot order and make the CD ROM drive number 1 in the order.  Place the DVD in the DVD drive, escape out of System Setup using the option to save changes, and allow the computer to boot.

    The only other way to get the DVD drive to boot is to physically move the master connector from the CD drive to the DVD drive.

  • 838

    0

    Posted October 14th, 2011 05:00

    The only other way to get the DVD drive to boot is to physically move the master connector from the CD drive to the DVD drive.

     Hmm! I think I did try that one, but I may have not done it right somehow. Is there anything special about DELL boxes I don't know? Could you elaborate a little more on "physically move the master connector from the CD drive to the DVD drive"?

     Thank you

     lbrtchx

  • jackshack

    6447 Posts

    838

    0

    Posted October 14th, 2011 14:00

    With all the info so kindly provided by Speedstep, you have probably figured out by now that you would need to unplug the ribbon cable connector (the black connector in Speedstep's graphic) from the CD ROM drive and plug it into the DVD drive.  Whichever drive is at the end of the cable is defined as the master due to the fact that Dell uses the Cable Select option on its computers.