UNSOLVED

OrangeBeard

updated

17 years ago

O

OrangeBeard

13 Posts

0

403468

October 28th, 2009 13:00

OptiPlex 960 A05 Windows 7 Pro 64 bit-- PCI Simple Communications Controller

Let me start by saying that the system is stable and everything appears to be working fine. I'm running Windows 7 Pro 64bit (RAID 0); all drivers from Support.dell.com have been installed in the correct order. However, in the Device Manager there is PCI Simple Communications Controller and Intel Active Management Technology SOL (COM4) with yellow exclamation marks.

The drivers for PCI Simple Comm... are not installed (Code 28) and cannot be found.

Hardware IDs:
PCI\VEN_8086&DEV_2E15&SUBSYS_02761028&REV_03
PCI\VEN_8086&DEV_2E15&SUBSYS_02761028
PCI\VEN_8086&DEV_2E15&CC_078000
PCI\VEN_8086&DEV_2E15&CC_0780

 

The drivers for the Intel AMT... "Windows has stopped this device because it has reported problems. (Code 43)" When I attempt to "Scan for hardware changes" via the Device Manager it will change the COM port successively, so instead of COM4 it will change to COM5, then COM6, etc. it works for a split second and then errors out again and the exclamation mark returns.

Hardware IDs:
PCI\VEN_8086&DEV_2E17&SUBSYS_00008086&REV_03
PCI\VEN_8086&DEV_2E17&SUBSYS_00008086
PCI\VEN_8086&DEV_2E17&CC_070002
PCI\VEN_8086&DEV_2E17&CC_0700

Further, I have run the 32 bit diagnostics and received the following error message:

USB TeacCorp DID=0200
Error Code 5E00:021F
USB_Device is not responding

I have also performed a vanilla install of Windows 7 Pro 64 (No RAID) bit (just to make sure it wasn't a botched installation and the same two devices display the same problems. I have uninstalled the devices and reinstalled them using the Dell drivers and the problem persists.

This is more of an annoyance if anything, but I am a perfectionist and cannot sleep at night thinking that there may be something wrong. Any one else have this issue? Suggestions?

Thanks!

OrangeBeard

 

  • OrangeBeard

    13 Posts

    2904

    0

    Posted October 28th, 2009 13:00

    I found out that the TeacCorp is the Card reader..I removed it and the problem persists with the device manager items; although now the Diagnostics finishes without error.

  • OrangeBeard

    13 Posts

    2904

    0

    Posted November 16th, 2009 15:00

    Anyone else experienced this problem? I have tried clean installs of both WIndows 7 Professional (64bit) and WIndows 7 Enterprise (64 bit) and the PCI Simple Communications Device and Intel (R) Active Management Technology - SOL (COM4) remain with a yellow exclamation point.

     

  • NoBeardy

    1 Message

    2904

    0

    Posted December 10th, 2009 09:00

    I have had the same Hardware IDs:
    PCI\VEN_8086&DEV_2E15&SUBSYS_02761028&REV_03
    PCI\VEN_8086&DEV_2E15&SUBSYS_02761028
    PCI\VEN_8086&DEV_2E15&CC_078000
    PCI\VEN_8086&DEV_2E15&CC_0780

    I installed both R229703 and R229705 from the dell drivers and these resolved the message.

    I've got an Optiplex 780 running Windows 7 32-bit.

    Hope this helps

  • paule123

    1 Rookie

    •

    56 Posts

    2904

    0

    Posted March 19th, 2010 15:00

    I installed both R229703 and R229705 from the dell drivers and these resolved the message.

     

    Thanks for this.  Both these packages also work perfectly on our Optiplex 960 running Windows 2008 Server (32-bit)

     

     

  • OrangeBeard

    13 Posts

    2904

    0

    Posted March 19th, 2010 15:00

    I replaced the motherboard via WPD and the drivers loaded fine. It was apparently a bad motherboard.