UNSOLVED

AlphaDubeSiegfr

updated

18 years ago

0

6506

September 23rd, 2008 04:00

Need a lot of Help!!! Urgent!!! I believe I fryed my XPS 730

Ok, I wanted to take advantage of the CrossFire on 790i motherboard of the XPS 730 so I bought 2 H 4870x2 to try quad crossfire. When I received them I realized that the power supply didn't have the required connectors to give those cards enough power so I decided to purchase a new PSU. I unistalled the previous PSU, put the new one on its place then I faced an other problem. The master control card, the one that connects all the fans and leds to the motherboard, uses a 10 pin connector that I haven't seen before. So, naively and stupidly, I decided to cut the pin from the Dell PSU and cut two connectors from the new PSU, then reconnect the connector of the Dell PSU with the cables of the new PSU. After that, I reasembled everything, connected everything and fturned my XPS on. It turned on but after a few seconds I heard a "pop" sound and then it started to smell like soething got burned. The computer was till on and it seemed to work fine but because I didn't know hwat was going on Idecided to turn it off inmediatelly. After that the computer doesn't turn on anymore.

 

I can see that energy goes to the motherboard becasue I see a blue and yellow led turned on next to the processor but thats all.

 

I'm not sure if the master board, the mother board, the new power supply, or all of them got fried. Sience I obviously voided my warranty I just want to know what's the procedure on this case. How much would I have to pay to get everything fixed. And if I find that everything is find except for one of those 3 components what would be the price to replace the mother board, or the PSU, or the masterboard?

 

Any extra help you can give would be really appreciated.

 

The XPS I ordered had the following: Q9550, 2gb ddr3 ram, radeon 3870 512mb, 2 500gb HD, standard multi-drive, creative x-fi xtremegamer, no monitor, no anything else. I then upgraded it with 8gb ddr3 ram and a radeon 4870x2 and was waiting for the new PSU to install a second 4870x2 in crossfire. Before this incident, the XPS with the 4870x2 and the 8gb was working just fine. My Os was windows vista basic 64. I never did any kind of overclock.

  • mischieff

    196 Posts

    249

    0

    Posted September 23rd, 2008 04:00

    I'm waiting for my 730 to arrive, ordered same basic setup as you but with plans to upgrade.

     

    You made a rather stupid decision, no offense, but the 730 has a standard 1000 watt PSU, more than enough for both of those cards.

     

    You can configure the 730 with dual GTX 280's from dells page, which has the Same power connectors as the 4870x2's ( 6 pin, 8 pin )

     

    All you needed was a few convertors? My GTX 280 here in the box came with them.

     

    What you needed was "2 4 pin molex to 6-pin" and "2 6-pin to 8-pin"

     

    So basically to power both of those cards, all you need is, 4 4-pin molex connectors available and 4 6 pins, using the convertors of course, i'm positive the 730 provides those.

    You probably just need a new master board.
    Message Edited by mischieff on 09-23-2008 12:42 AM
  • 249

    0

    Posted September 23rd, 2008 04:00

    Yeah I know it was stupid but the damage is already done so I'm gonna try to save whatever I can. From the preliminary test that I have made I think that just the master control card got fried. The PSU and the Motherboard seem to be fine. Tomorrow I'm gonna buy some extra things to further test the mobo and the PSU. If I'am able to boot into windows and run 3dmark vantage then I can conlcude that except for the master control board everything is fine, if not I guess everything goes to the trash.

     

    If just the master control board was fried I would like to know what is the price of a new one.

     

    If the mobo, the master control, and the PSU are dead I guess I'm gonna buy a x48 mobo and a new PSU and trash the fried ones cuz I don't wanna give away the case. I can still connect the led lights and the fans to a fan and light control from frozen cpu and get everything back just the way it was (with some modifications of course).

  • kjdocs

    32 Posts

    249

    0

    Posted September 23rd, 2008 12:00

    Good Luck Alpah, I like your attitude!  Hope you get it fixed :)