Ques

updated

18 years ago

Q

Ques

31 Posts

0

9327

December 3rd, 2008 09:00

I Just Purchased a LG: GH22NP20 Hard Drive for My Dell Dimension e 310 and Having Problems Plz Help.

I just purchased a LG GH22NP20 Hard drive for My Dell Dimension E 310 and when I install the drivers for my Nvidia 6200 video card onto my computer and restart my computer, the welcome screen won't appear, I get a black screen.

The minute I go into safe mode and uninstall the Nvidia drivers and restart my computer, the welcome screen appears. This has happened since I installed the new harddrive and I need the drivers to my video card in order to play games on my computer. But if I install the nvidia drivers, then I can't get into windows?

Can someone please tell me why this is happening? And how I can resolve this? I went on the LG website and couldn't find any drivers to download for this harddrive?

Your advice will be greatly appreciated:emotion-5:

  • Hanspuppa

    799 Posts

    656

    1

    Posted December 3rd, 2008 13:00

    Hello Ques, Sorry for the confusion. I thought you added a drive and had two optical drives installed in the system.

    If you removed the original drive and installed the new LG GH22NP20 and connected it as the original drive was, it should be fine.

    You may want to just check the jumper settings to make sure is it set to CS (cable select) and it is on the very end connector of the cable.

    If it happens to be set as Slave and it is the only drive on the cable, you will get an error.

    Most drives are shipped CS now, but I would check to be sure. The "M" stands for Master and the "S " stands for slave.

    If you had two drives, one would need to be set as Master on the end connector and the other would need to be set as slave and connected to the middle connector of the cable, or both could be set to CS and they should be recogonized.

    I can't imagine why the video issue is appearing. If the system boots to the desktop, some video drivers are loaded and being used. They may be the generic Microsoft drivers.

    After I checked to insure the new optical drive settings are correct (CS), I would boot the system and go into the Control Panel Device Manager, and see if there are any red x or yellow question marks that indicate any problem with any device.

    It does really appear that you may be installing the wrong video drivers even though you have done this for a while now, or they are corrupt.

    Does your video card require additional power cables attached to it. You might give the cables a good inspection when you check the DVD drive.

    Keep us updated if it does not work, and there may be some more suggestions.

  • Hanspuppa

    799 Posts

    656

    0

    Posted December 3rd, 2008 09:00

    Hello Ques, You seem to have a few possible issues going on here.

    First, the LG GH22NP20 is not a hard drive, but instead, a CD\DVD Reader\Burner.

    It is also an IDE and not a SATA. Since you mentioned you replaced the drive, you may not have the jumper set properly.

    The are three ways to set the jumpers, depending on your other IDE drive in your system.

    If you have another CD\DVD drive, you would need to check the jumper settings on the original drive and then you could set the jumpers on the new LG GH22NP20 accordingly.

    I would set the jumpers on both CD\DVD drives to CS (cable select) and connect the IDE (ribbon cable) top connector to the first CD\DVD drive and the middle connector to the second drive below the first. Since the ribbon cables are short on the two connector ends, this seems to work best.

    You mentioned the system would not now boot and you updated the video card drivers. Did you use the recommended driver for your video card. The reason I mention this, is that you video card is onboard and will need the drivers for this video card to be specific to the video card and not just any Nvidia or ATI drivers.

    Just take a look at the jumper settings on the CD\DVD drives and adjust them if necessary.

    If the system will not boot afterwards, you may have to do a Repair install of the OS.

    Please let us know how you come out and if you still have problems, maybe we can suggest some other options.

    Hope this helps.

  • Ques

    31 Posts

    656

    0

    Posted December 3rd, 2008 12:00

    Thank you for your help I truly appreciate it. I currently have one IDE drive installed and that's the LG GH22NP20 I have another slot where I guess I could add a second cd drive if I wanted. So are you saying to install the original cd drive back into the system and add the new cd drive into the second slot??

    I was also told in another thread to set the cables to CS and that the back of the drive is labeled CS, M, and S but since I bought the drive "OEM" which I just learned what that meant yesterday, it did not come with manual instruction, I believe it came with CD instruction but would good is having the instruction on CD when you're trying to install the drive that the CD needs to go in.

    And yes, I did install the correct drivers for the video card. I've had the video card for over a year now and I've been downloading the drivers straight from the nvidia website. The problem I was having was that since installing the new cd/dvd drive the system would boot w/o the drivers installed but the minute I would install the nvidia drivers the system won't boot and a black screen appears and this is since adding the new cd/dvd drive.

  • Ques

    31 Posts

    656

    0

    Posted December 4th, 2008 14:00

    I went into Device Manager and there were yellow questions marks on Other Devices: PCI Simple Communications Controllers and VGA controllers. When I install the nvidia drivers and go into safe mode, the VGA controller no longer has a question mark but the PCI Simple Communications Controllers does.

    But yet instill, when I reboot, I still get the black screen until I uninstall the nvidia drivers.

    I even reinstalled the old cd/dvd ide drive and couldn't believe that I was experiencing the same problem when I never experienced this problem while having this particular ide drive.

    So now that I know that the black screen is happening regardless to whether the old ide drive or the new ide drive is installed and that there are yellow question marks on other devices: PCI Simple Communications Controllers and VGA Controllers, what do I do now?

    I have reformatted my computer around 3 or 4 times in the past two/three months, is it possible that I'm forgetting to install a dell driver?

    At this point I don't know what to do, my old ide driver does not play CDs or games but it plays DVDs which is why I had to purchase a new ide driver. Am I better off with a SATA driver or is this a problem that has nothing to do with the ide driver?

     

  • Hanspuppa

    799 Posts

    656

    0

    Posted December 5th, 2008 11:00

    I have reformatted my computer around 3 or 4 times in the past two/three months, is it possible that I'm forgetting to install a dell driver?

    Hello Ques, Sorry for the no response. I thought the issue was resolved. I haven't been keeping up with it lately.

    It is quite possible that you are not installing the Dell drivers needed for the system to work properly after the reformats.

    The Yellow Question marks usually indicate that the drivers for the device have not been installed.

    I have never seen the PCI Simple Communications Controller in the Device Manager, but I suspect it may have something to do with a modem or other Communications device.

    A driver install for this would probably correct this.

    I would reconnect the DVD that you put in following the procedure mentioned, and since you recently reformatted, you probably have your needed backups.

    After each reformat and fresh OS install, you should install all the Dell drivers for your system, starting with the Chipset drivers first, then the video card drivers. I, like you mentioned, use the video card drivers from the manufacturer's site, since they are newer versions.

    Then install the other drivers, such as network, and any others needed for hardware on your system.

    If these drivers are not installed properly, you will receive all sorts of issues.

    If you system has the Dell Recovery Restore Utility on it, I would use that to put it back to the day it was shipped.

    if it does not, a reformat and and fresh install of the OS and programs will result in the best possible solution, if there are no hardware issues.

    I just went to the Dell Web site and looked up the specifications for your E310. It shows the video card is an Intel and not Nvidia. That may be one of the issues with your system if you are installing Nvidia drivers for an Intel video card.

    Below is a link to the Dell web site drivers for your system. You might go there and download all the drivers you may need.

    There seems to be 2 different Intel video drivers listed, so I don't know which one you need for your system. You can check this in the Device Manager and see which one you have.

    E310 Drivers

    I just had another thought about your issue. Since you mentioned you could boot into Safe Mode and all seemed OK, and then you tried to boot normally and got a black screen, this sounds exactly like you have the incorrect video drivers installed.

    When booting into Safe Mode, only the drivers neccessary to open the desktop are loaded, and in your case, Microsoft generic drivers for the Intel video card.

    But when booting normally, the OS recogonizes the Intel onboard video card and searches for the drivers for it, and not finding them, the black screen and freeze appears.

    keep us updated and we can get this issue resolved.