UNSOLVED

jhar

updated

19 years ago

J

jhar

43 Posts

0

6006

January 9th, 2008 18:00

Attn: 720H2C + QX6850 owners...is your system stable?

Hey guys...as you can tell from the title, I've got the 720H2C system with the QX6850 chip.  I'm also running bios A04.  The chip itself seems very stable (solid through EVEREST benchmarks, Prime95 etc).
 
Previously, I had the QX6800 chip, which was stable but not overclockable (one of the first of the famous unstable batch on the early 720 releases, already covered ad nauseum).  However, my system ran great.
 
The problem I am now having since the processor upgrade is video unstability (I think).  I have dual 8800GTX's.  I am experiencing constant BSOD's in XP (this is through many fresh installs with current NVidia drivers (169.21), older WHQL NVidia drivers, and even ancient Dell website NVidia drivers).  Moving to Vista 32 and 64 (again, fresh installs), same thing, only the dreaded TDR errors instead.  I've also tried switching the cards around and flipping the SLI bridge around.  Nothing is working. 
 
Please note, I've run through these fresh installs with the QX6850 parked at Bin+0, to help rule out the proc.
 
Any suggestions out there?  Fellow 720H2C + QX6850 owners...are your systems stable?  Is this a BIOS thing or something else?  If so, will A05 address this issue?
 
Lastly, can someone confirm that in terms of the power supply to each card, each card gets a white and black plug (there are 2 white power plugs and 2 black power plugs).
 
THANKS IN ADVANCE
  • jhar

    43 Posts

    594

    0

    Posted January 9th, 2008 19:00

    I should also point out that I even reset the CMOS and completely reformatted the hard drives before each new OS install.
     
    As well, if anyone is familiar with the S&M 1.91.1 benchmark, everything checked out until I got to the Power Supply/Video Heat test.
     
    Thanks everyone...
  • Racey1979

    52 Posts

    594

    0

    Posted January 9th, 2008 19:00

    Hello mate, can't help you with the stability issue, as I only have the coal powered QX6700! Lol. What I can tell you is there is one white connector and one black connector. Well two of each to be more precise. Mine has two white on the top GPU and two black on the bottom GPU.
     
    Cheers
     
    Andy
  • jhar

    43 Posts

    594

    0

    Posted January 9th, 2008 19:00

    thanks brother...I did realize after I removed the cards to reseat them, that I failed to write down which power connectors went where...the manual does not state as much
     
    I did think that might be an issue too so I tried both scenarios (black + white on both, black/black + white/white)...no luck
     
    appreciate the reply so far
     
    cheers
  • cademetz

    2 Intern

    •

    1327 Posts

    594

    0

    Posted January 9th, 2008 19:00

    This post has been removed in protest of DCF's and Dell's policies, behavior, lack of respect, and poor treatment of the community.
    Message Edited by cademetz on 06-27-2008 11:42 PM
  • NovaCX12

    66 Posts

    594

    0

    Posted January 9th, 2008 20:00

    Hello, have you looked at your ram, how much do you have? If you have 4GB, try 2GB.
  • jhar

    43 Posts

    594

    0

    Posted January 9th, 2008 21:00

    guys...thanks for the posts...I have 2 x 1gb of the Corsair Dominator (CM2X1024-8500C5D).  I've tried disabling EPP too but same thing still happens.
  • gdwrnch3

    2 Intern

    •

    3278 Posts

    594

    0

    Posted January 9th, 2008 21:00

       I've got a 720 air cooled on the A04 bios, with the QX6850, but only one 8800gt, and it's stable as a rock.
  • mickelodian

    14 Posts

    594

    0

    Posted January 10th, 2008 06:00

    I have the 710 H2c with the x6800 chip which is overclocked from the factory but I can't run it overclocked at all. Bin+0 for me as well. I am in discussions with support at the moment and hope that they will resolve this situation.
  • 594

    0

    Posted January 10th, 2008 07:00

    Hello
    For information!
    I have a 720 H2C with QX6850 a 4.0 bin +3 4 gigabytes of ram 2 8800 GTX 1 physX an X-Fi Platinum, BIOS A04, all the elements seem excessive heat, but remains very stable even during the games (UT3 Crysis ...)
    PS: I disabled in the bios visualization.
    Vista 32-bit SP1.
  • jhar

    43 Posts

    564

    0

    Posted January 10th, 2008 12:00

    Thanks everyone.  Actually, my chip seems to run perfectly at Bin + 4 (4.0ghz) too.  It passes stability tests like S&M and Everest.
     
    My system crashes on video benchmarks and tests, and I can't run any game without it crashing 3 seconds into any 3d rendered scene.
     
    I will try disabling visualization tonight.  I did already try it with the default bios settings with no luck, but I can't remember if visualization is defaulted to off (I'm at work).  I'll try it later.
     
    Thanks for the help so far!