Papa10_233f86

updated

16 years ago

0

6638

October 6th, 2010 11:00

Powerpath only shows 1 adaptor

Not sure if this is the correct forum but...

I have a CX3 with 10 hosts connected to it.  The array has been up and running for 2 years.   Yesterday, I was adding a host and everything went fine.  I installed PowerPath, Navisphere host agent, Updated my HBA drivers, zoned the switches and added my storage.  It is all working fine.   Today, I opened PowerPath and noticed I only had 1 adaptor listed.   I don’t remember if it was there yesterday but it is not there today.   If I look under connectivity status in Navisphere all of the WWNs are listed, logged in and registered.  This is happening on all 4 servers I just connected to the array yesterday.

Can anyone tell me why PP only shows one adaptor?

  • kelleg

    6 Operator

    •

    4537 Posts

    1933

    0

    Posted October 7th, 2010 10:00

    quick, quick, click the reconnect button

    When you first install a new host, in Connectivity Status the icon color with be BLUE - this means that the HBA is logged in and Registered but not yet assigned to a Storage Group - in this state the HBA's are assigned to the ~Management storage group - a holding place until you add the host to a Storage Group - when you do, the icon will turn GREEN. Sometimes the HBA does not get added correctly - like when you replace an HBA.

    After you click the reconnect, the HBA's show show up in the correct SG - you'll have to rescan from the host

    glen

  • 835

    0

    Posted October 6th, 2010 12:00

    C:\Program Files\EMC\PowerPath>powermt display dev=all
    Pseudo name=harddisk3
    CLARiiON ID=APM00080xxxxxx [servername]
    Logical device ID=6006016070A6xxxxxxxxxxxxxxxx [LUN_Name]
    state=alive; policy=CLAROpt; priority=0; queued-IOs=0;
    Owner: default=SP B, current=SP B       Array failover mode: 1
    ==============================================================================
    --------------- Host ---------------   - Stor -   -- I/O Path --  -- Stats ---
    ###  HW Path               I/O Paths    Interf.   Mode    State   Q-IOs Errors
    ==============================================================================
       1 port1\path0\tgt0\lun0    c1t0d0    SP A4     active  alive       0      0
       1 port1\path0\tgt1\lun0    c1t1d0    SP B5     active  alive       0      0

  • kenn2347

    4 Apprentice

    •

    542 Posts

    1275

    0

    Posted October 6th, 2010 12:00

    what does a powermt display dev=all show you?

    do you hvae 4 paths in that display?  if so,  it might just be a graphical error.

  • kenn2347

    4 Apprentice

    •

    542 Posts

    1274

    0

    Posted October 6th, 2010 12:00

    You can check the license by going to Start>EMC>Powerpath>License tool or something like that.

    It will be listed in that box

  • 1275

    0

    Posted October 6th, 2010 12:00

    Each host has 4 connections A-5, A-4, B-5, and B-4.

  • Jen_LeClair

    111 Posts

    883

    0

    Posted October 6th, 2010 12:00

    Did you enter the PowerPath license? With out the license key you only get support for one HBA.

  • Jen_LeClair

    111 Posts

    549

    0

    Posted October 6th, 2010 12:00

    Have you verified that you have the failover proberties set correctly for you configuration?

    EMC KB article emc99467 contains all of the setting by OS type.

  • kenn2347

    4 Apprentice

    •

    542 Posts

    835

    0

    Posted October 6th, 2010 12:00

    ok so PP is only showing one HBA and it is not a graphic issue.  What type of HBA is it?  Qlogic?  what does SanSurfer show?

  • kenn2347

    4 Apprentice

    •

    542 Posts

    882

    0

    Posted October 6th, 2010 12:00

    The command i mentioned about is done on the host that powerpath is installed on.  navigate to the installed directory and run that command.  maybe you can copy and paste the results here

  • kenn2347

    4 Apprentice

    •

    542 Posts

    1275

    0

    Posted October 6th, 2010 12:00

    When you look at connectivity status, how many initialtor records are you seeing for those 4 hosts?

    Dual port HBA or 2 single port hba's?