UNSOLVED

tjmjcp

updated

17 years ago

T

tjmjcp

4 Posts

0

2107

February 3rd, 2010 12:00

Celerra/ns480 datamover connectivity question

On a NS480 with four blades and 4 connections per blade (2 to each switch in a dual switch network), how many connections per blade are active/passive?

  • nandas

    6 Operator

    •

    1473 Posts

    314

    0

    Posted February 3rd, 2010 13:00

    It depends on the Network configuration on the Blade (which you have not mentioned). It will depend on whether you are using any Trunk configuration (Etherchannel or LACP) or FSN (Fail safe network) or both.

    It can be of varios combinations as follows -

    1) Four active connections per blade - if no trunk or FSN is configured

    2) Four active connnections per blade - if two x 2-port trunk is configured. Each trunk will be of 2 active ports and both trunks are active

    3) Four active connections per blade - if one single trunk is configured with all 4 ports - in this case, the Ethernet switches must support channeling across switches

    4) Two active connections per blade - if you have Fail safe Network configured - it can be of two combinations again     

              a) One active 2-port trunk and one passive 2-port trunk. I.e. you have two trunks (each having 2 ports) configured - one trunk goes to one switch and the other trunk goes to the second switch - one trunk is primary and the other is standby.

              b) two individual active ports (going to one switch) and two individual passive ports (going to the second switch) - no trunk configuration.

    As a common configuration -  your configuration may be most likely either 2) or 4)a)

    Thanks,
    Sandip

  • eliza1

    17 Posts

    314

    0

    Posted April 13th, 2011 16:00

    Can someone review the configuration below and let me know if it is workable?

    DataMover1:

    fge0 cables to SW1

    fge1 cables to SW2

    setup an LACP connection on fge0-fge1 in Celerra, setup a port channel connection on Nexus 7K1

    cge0 cables to SW1

    cge1 cables to SW2

    setup an FSN connection on cge0-cge1 in Celerra, setup a port channel conection on Nexus 7K1.

    Same config for DM2.

    Thanks

  • dynamox

    11 Legend

    •

    20419 Posts

    •

    87439 Points

    314

    0

    Posted April 13th, 2011 17:00

    vPC on 7Ks for LACP trunk on Celerra ?

  • dynamox

    11 Legend

    •

    20419 Posts

    •

    87439 Points

    314

    0

    Posted April 14th, 2011 07:00

    looks good to me , for FSN connection ..you don't need to do anything on the switch side though, you just configure FSN on Celerra and you are ready to go.

  • eliza1

    17 Posts

    314

    0

    Posted April 14th, 2011 07:00

    yes.  Thanks.

  • eliza1

    17 Posts

    314

    0

    Posted April 14th, 2011 08:00

    Do you mean a FSN connection for cge0-cge1?

    Just thought port channel on 7K for FSN connection will allow more bandwidth.  

  • dynamox

    11 Legend

    •

    20419 Posts

    •

    87439 Points

    314

    0

    Posted April 14th, 2011 08:00

    In FSN configuration, one device is active and the other one is passive. Instead of FSN ..why not do another LACP trunk with cge0 and cge1. Since you have the fancy 7Ks that allow vCP, you are not losing any redundancy yet gain more performance.

  • dynamox

    11 Legend

    •

    20419 Posts

    •

    87439 Points

    314

    0

    Posted April 14th, 2011 09:00

    Can we do something like below (to complicate things more )?

    LACP0 - fge0-fge1   (port channel in 7K)

    LACP1 - cge0-cge1  (port channel in 7K)

    FSN0 - LACP0 active, LACP1 passive

    you absolutly can.

    Once you create FSN0 device, thats' when you assign interfaces ( IP Address).

  • eliza1

    17 Posts

    151

    0

    Posted April 14th, 2011 09:00

    Thanks.

  • eliza1

    17 Posts

    314

    0

    Posted April 14th, 2011 09:00

    Thanks for the clarification on FSN and suggestion.

    Do we need 2 IP addresses for each LACP connection?  Which IP address users connected to?  

    Can we do something like below (to complicate things more )?

    LACP0 - fge0-fge1   (port channel in 7K)

    LACP1 - cge0-cge1  (port channel in 7K)

    FSN0 - LACP0 active, LACP1 passive