UNSOLVED

onealien

updated

5 years ago

O

onealien

1 Rookie

•

11 Posts

0

10771

February 4th, 2022 09:00

Aurora R13, can't overclock at all. What is the right way to go about it?

Hi,


I bought an Aurora R13 with i9-12900KF, RTX 3080TI, 750PSU. This seems to be a decent PC overall however its clock seems to be locked to run 4.8GHZ at max, even that I cant seem to be able to get stable 4.8 Not just the clock speed varies below 4.8, the XTU benchmark speeds varies like 500-600 points up and down without any changes. I can get 8500 range or 9100 marks at random times, I do not get why it varies so much. The same PC, same conditions, same apps in the background.

 

645494_360842_05_front_zoom.jpg


I tried Alienware's OCC at 5.0, 5.1, 5.2 and 5.3 All run below 4.8GHZ range, so those settings do not seem to be doing anything at all. I check it with CPUZ and XTU.

Then I installed Intel's XTU and played with varies numbers for various cores, disabled Turbo Boost stuff etc, tried manual voltage upto 1.4v with various voltage shifts I can't get this PC to go above 4.8 stable. The speeds are throttled around 95+C

Another thing is that the OC settings are disabled in the BIOS. I can get them show up if I apply the optimized settings but they are disabled again in the next boot after I try OC LV1 or OC LV2 as shown in the Aliennware OC docs.

I spent so much money on this PC, so that I can use it for 3D stuff and I am hoping to run it at @5.0 or @5.1 I am not even pushing this to the limits of the CPU's advertised limits.

What is the right way to do the overclocking with this PC? Are the BIOS/drivers intentionally blocking overclocking? Did I just get a bad build with bad temps?

I might end up sending this back if I can't get this going, because that couple hundred mhz per core makes alot of speed difference in my work.

thanks

  • dbrewster

    3 Novice

    •

    237 Posts

    •

    852 Points

    4393

    1

    Posted February 4th, 2022 09:00

       Hiya man,  Im a pc user and not a tech so read this at your own risk.  You know the awcc must reboot to apply some of the options in the occ.  Also that If you do custom oc in the awcc occ that the bios will Grey out the options in performance and indicate 'customized' vs.  oc 1  or oc2.  And that if you wish to change this u must reset to default the bios entries and go from there.  I have only my second AW pc, but I've had success with the awcc occ.  The sliders are usually very easy and saving to a new profile is simple and user friendly, except that if reboot is necessary that it only reminds you once and if you are busy you could think that the settings were applied when the system tested the new values. All my sliders are yellow/green no red or pink LOL.  G'luck

     

  • onealien

    1 Rookie

    •

    11 Posts

    4353

    0

    Posted February 4th, 2022 14:00

    Ok, well I "applied" 5.2 restart it the PC, and it is still capped at 4.8Ghz I do not get this to be honest.

    Here is a screen video taken from XTU showing the  issue I am trying to explain. 

    https://imgur.com/a/AFLEsnY

     

     

  • onealien

    1 Rookie

    •

    11 Posts

    4358

    0

    Posted February 4th, 2022 14:00

    Hey thanks for the reply. Is applying the OC with CC basically clicking on a profile and make sure there is a check mark next to it?

  • dbrewster

    3 Novice

    •

    237 Posts

    •

    852 Points

    4340

    1

    Posted February 4th, 2022 16:00

    well yes.  On the home tab though you should be able to see the profile that is active for each category of OC. Like thermal,cpu,power management and audio, and these are selectable from that screen also, and should warn if a reboot is necessary,  power management profile includes settings fo minimum and maximum processor states so choose high performance and check that these donnot say anything less than 100%.  I always use the awcc for overclock. I have been into xtu but I found this awcc easier.

  • Jonny

    1 Rookie

    •

    110 Posts

    4305

    1

    Posted February 4th, 2022 23:00

    I’ve found Alienware CC kills some performance on the R13 on Cinebench Timespy etc, quite a bit actually both single and all core 

    It also gives me the variation in results back to back you are talking about.

    So all I use it for now is setting the lighting and fan speed.

    When I turn on my pc I never open ACC. The lighting you have chosen comes on after a short time.

    I over clock in Bios.

    You should notice a big jump in performance on the CPU doing the above 

     

  • Jonny

    1 Rookie

    •

    110 Posts

    4302

    1

    Posted February 5th, 2022 00:00

    For example Cinebench R23

    Alienware CC on 1850 single core

    Alienware CC off I always break into the 2000’s single 

    Same on Multi Core test / BIG variety in results when run back to back.

    Time spy my CPU result 

    Alienware CC on 16000 - 16500 CPU score.
    GPU always sits around 19000 with no clock

    Alienware CC off 17500 CPU, with tests back to back.

    I had the same headache as you with Alienware CC

     

  • onealien

    1 Rookie

    •

    11 Posts

    2000

    0

    Posted February 5th, 2022 09:00

    What is your Intel XTU benchmark 2.0 score?

  • onealien

    1 Rookie

    •

    11 Posts

    4270

    0

    Posted February 5th, 2022 09:00

    Hi,

    Thanks for the reply. Could you please tell me the exact steps you take to do this in the bios? There does not seem to be much of any setting in the Bios, plus  trying to set to OC LV1 or OC LV2 (after applying optimal defaults) casues multiple reboots during initial reboot and then it disables the performance options again.

     

    So far this has been the most confusing and convoluted OCC attemp I have ever tried, anb I owned tons of computers.

     

     

     

  • Jonny

    1 Rookie

    •

    110 Posts

    4265

    0

    Posted February 5th, 2022 09:00

    Hi 

    I just use OC LV2 in Bios, nothing fancy.

    But the fact you are having multiply reboots sounds like you have an underlying problem when trying to OC. 

    I’m on the latest Bios as well, but I haven’t had any issues and any Bios so far (touch wood).

    I would give Tech a call and see if they can help you sort the reboots.

    Quick question, you haven’t added any fans have you that maybe are causing the reboots? That is the only time I have had a problem with reboots when selecting OC in Bios.

  • onealien

    1 Rookie

    •

    11 Posts

    4261

    0

    Posted February 5th, 2022 09:00

    Thanks,  I will try that again.  I am worried that this PC is not outputting enough power to the CPU, because I see Power limit throttling and  EDP limit throttling are also kicked in during benchmark along with Thermal throttling even at 4.8.