UNSOLVED

velopirate

updated

20 years ago

0

5499

February 26th, 2007 10:00

Intel Matrix Console and RAID will not work hard drive upgrade

I needed to increase the storage on my E510 so I swapped the two Toshiba HD160JJ/P drives that came with my Dimension to two WD3200KS drives from Western Digital.  I had no problems bringing my image over to the new drives and booting up.  However, I cannot create a RAID 1 environment now (critical to me) and Intel's Matrix Storage Console will not install ("system does not meet minimum requirements.")  I checked the BIOS and, to me, everything looks as it should.
 
Any suggestions on getting RAID 1 to work would be much appreciated.  I am running Vista Ultimate.
 
Thanks!
Mike
 

BIOS
BIOS Vendor: Dell Inc.
BIOS Version:  A07
BIOS Date:  01-08-07

Processor
Manufacturer Intel(R) Pentium(R) D CPU 3.20GHz Clock Speed 3.2GHz L2 Cache Size 4096
 
IDE ATA/ATAPI Controllers
Intel(R) 82801G (ICH7 Family) Ultra ATA Storage Controllers - 27DF ATA Channel 0
Intel(R) 82801GB/GR/GH (ICH7 Family) Serial ATA Storage Controller - 27C0 ATA Channel 0 ATA Channel 1
 


Message Edited by velopirate on 02-26-2007 09:13 AM

Message Edited by velopirate on 02-26-2007 09:15 AM
  • mombodog

    2 Intern

    •

    12735 Posts

    775

    0

    Posted February 26th, 2007 19:00

    You can configure raid in the bios then use the ctrl+I keys to set up the drives, but this may require reinstallation of the OS, but does not require the software you are trying to install.
     
    Check your bios settings to be sure it is set to allow raid configuration of the drives. Then do the ctrl+I  just after post to enter the intel raid config, see if you can set up raid 1 from there.
     
  • 775

    0

    Posted February 27th, 2007 05:00

    mombodog,
     
    Thanks for the reply.  Unfortunately, this did not work.  Even after changing the BIOS to force RAID (instead of automatically choosing RAID if the drives are signed), I am still seeing that these drives are non-RAID hard drives.  Pressing CTRL+I at boot only gave me the options of booting into Vista or running a memory check (don't recall the exact phrasing).  However, I was able to install the Intel Matrix Storage Console.  :smileywink:  However, this also shows both hard drives and being non-RAID drives.
     
    Just curious...could this have something to do with Vista?  Vista is using generic Microsoft drivers for these two hard drives.  I have tried updating the drivers, but nothing better can be found.
     
    -Mike
  • 775

    0

    Posted February 27th, 2007 13:00

    F12 does get me the boot menu. Ctrl+I appears to be some type of configuration screen, but RAID was not one of the selections.

    Message Edited by velopirate on 02-27-2007 09:16 AM
  • mombodog

    2 Intern

    •

    12735 Posts

    775

    0

    Posted February 27th, 2007 13:00

    page 29 of that pdf link above says it should, but is also says the bios needs to be set to "raid on" first. Check this setting again to be sure it took, then see if the Intex matrix storage manager will work in XP. 
     
     
  • mombodog

    2 Intern

    •

    12735 Posts

    775

    0

    Posted February 27th, 2007 13:00

    ctrl+I should get you to the Intel raid configurator, F12 gets the boot screen, not sure what is going on.
  • 775

    0

    Posted February 27th, 2007 14:00

    It is set to RAID ON and Matrix Storage Manager shows both drives (but as non-RAID drives). At this point, I can't go back to XP.