UNSOLVED

TDmail

updated

22 years ago

T

TDmail

10 Posts

0

5593

August 12th, 2004 20:00

Hard drive undetected during Windows restoration - need drivers

Greetings:

I wish to perform a complete re-installation of Windows XP on my new Dell system in order to get rid of unwanted pre-loaded material. However, I am having difficulty re-installing from the Dell-supplied restoration CD.

Problem:

After booting from the restoration CD and choosing to re-install Windows XP, the Windows setup program reports the following message:

"Setup did not find any hard disk drives installed in your computer"


(Note: When booting normally from the hard drive, no problems are encountered.)


Some relevant hardware details about my PC:

- Dimension 8400 series PC

- Intel 82801FB Serial ATA AHCI disk controller (according to Windows Device Manager)

- 160gb Western Digital serial ATA hard drive

- 3 1/2" floppy drive


Some relevant BIOS details:

- Under the "Drives" tab, "SATA Operation" is set to:
"RAID autodetect / AHCI".

- Other possible settings for "SATA Operation" include:
"RAID autodetect / ATA"


Windows version: Windows XP service pack 1a


Speculation:

It seems that Dell supplied an out-of-date restoration CD which does not include the proper drivers for detecting the hard drive controller while it is set to AHCI mode.


Possible resolutions:

Option 1: Dell provides me with a restoration CD witch has the necessary drivers included. (I'm not holding my breath on this one...)

Option 2: I can set the "SATA Operation" BIOS setting to "RAID autodetect / ATA" and perform the windows re-install normally. Windows setup does detect the hard drive when ATA mode is in use rather than AHCI. However, I'm unsure what the implications of choosing this option are: I suspect that I will be sacrificing performance for compatibility. (?)

Option 3: I can provide vendor-supplied AHCI drivers during the installation process. I know that pressing the [F6] key when the restoration CD is booting will cause Windows setup to prompt me for a floppy disk containing drivers for unsupported drive configurations. While I assume that I would get such drivers from Intel, I'm not really sure what I'm looking for. I need something that will fit on a floppy and be accepted by Windows setup. I gather I may also need to download the latest Intel INF update tool for my chipset and install that as well.

If anyone can provide technical insights into this issue, or supply links to needed drivers, it would be greatly appreciated.

-Junkman01
  • Coneypark

    58 Posts

    509

    0

    Posted August 12th, 2004 23:00

    Dell have not shipped you an out of date restall CD. Winows XP does not support SATA hard rives during install.

    You will need to create a floppy disk - I have given some links and details below.

     

    You can download them from Dell web site.:-

    http://support.euro.dell.com/uk/en/filelib/download/index.asp?fileid=R78496&sid=DIM_PNT_P4_8400&st=

    You need a floppy disk as this programme will create a floppy disk for you. Once the disk is created start up from Windows CD again

    and when  the propmtcomes up "Press F6 to install third party drivers" press F6. Windows will continue to copy files over and then it will ask you to insert your floppy disk that you created. Dont take the floppy disk out till windows tells you to.

     There are good instructions for this on the intel web site:-

    ftp://aiedownload.intel.com/df-support/7657/ENG/Readme.txt

    3.  At the beginning of the operating system setup, press F6
        to install a third party SCSI or RAID driver.

    4.  When prompted, select 'S' to Specify Additional Device.

    5.  When prompted, insert the floppy disk you created in
        step 2 and press Enter.

    6.  At this point you should be presented with a selection
        for one of the following depending on you hardware
        version and configuration:

    - Intel(R) 6300ESB SATA RAID Controller
    - Intel(R) 82801ER SATA RAID Controller
    - Intel(R) 82801FR SATA RAID Controller
    - Intel(R) 82801FR SATA AHCI Controller

    7.  Highlight the selection that is appropriate for the
        hardware in your system and press Enter.

    8.  Press Enter again to continue. Leave the floppy disk in
        the system until the next reboot as the software will
        need to be copied from the floppy disk again when setup
        is copying files.

    Hope this helps.

  • TDmail

    10 Posts

    509

    0

    Posted August 13th, 2004 01:00

    Coneypark:

    Thanks that is what I needed.

    -Junkman01