UNSOLVED

md12345

updated

16 years ago

M

md12345

4 Posts

0

89781

March 9th, 2011 18:00

Password Reset on 5012

I have been doing some searching on the net to figure out how to reset the password on this unit.

Basically following the instructions to hold the esc key during boot gives me the boot from flash/network option, booting from flash just gets me back to the password prompt, booting from network wants to load firmware.  I figured that loading firmware might wipe some of the settings (Hoping) and proceed to load the latest firmware which worked fine but I am still locked out.

Please help.

Thanks!

  • 1399

    0

    Posted March 10th, 2011 02:00

    Hi MD12345,

     

    To reset the password from the PowerConnect 5012 you can try entering the command prompt for emergency password reset or restore factory defaults and login with default username "root" and default password "switch"

    1. Connect to the switch via the console port and manually reboot the switch
    2. As soon as power is applied, press and hold the ESC key
    3. At the command prompt, type “EmergencyPasswordReset” (case-sensitive without the quotation marks)
    4. At the confirm (Y/N) prompt, type X
    5. If done properly, you will receive a message stating that the password has been disabled
    6. Type G and hit enter to reboot the switch

    The switch will reboot with the password disabled.

    For information about restore to factory defaults here the link to online manual for PC5012
    <ADMIN NOTE: Broken link has been removed from this post by Dell>

    Regards,

    Rodger 

  • 1399

    0

    Posted March 10th, 2011 04:00

    Hi MD12345,

     

    found a post where a user with the same issue like you describes, what he has done to get the command prompt.
    Can you please try this one?

    "My mistake was hitting escape *after* I applied power to the switch – you have to be very quick to catch it! It’s far easier to hold down escape in hyperterminal (or teraterm!) *before* you apply power and keep it down until you get the correct prompt."

    Please let me know your results,

    Thanks and Regards,

    Rodger 

  • md12345

    4 Posts

    1399

    0

    Posted March 10th, 2011 04:00

    As I stated orginaly that when I hold the esc key down I get the prompt of where I want to load from.  

     

    This is what happens when I boot holding the ESC key - This instance I pressed F to load from flash, If I try to type the "EmergencyPasswordReset" at that point as soon as I hit the n it starts the network boot to load firmware.

     

    Thanks

    Mike

     

    RDU Product coming up...

      CPU type is RC32332 revision 0x00
      DRAM found is 16MB
      Testing DRAM...OK


    Booting up...                           Ver 4.5.2214 (20020530)


    Reading non-volatile data...


    Boot from flash...


      Boot Mode (F)lash or (N)et: Ff


    Reading image from flash...   0%  6% 13% 20% 26% 33% 40% 46% 53% 60% 66% 73% 80% 87% 93% Done.


    Decompressing image...  Done.

    Expanded to 2827856 bytes, CRC 93210295



    Loading image...                        Release 6.1.2.3291 (07210816)


      Code Size............................6824K
      Total Free Memory Size...............9560K
            Start Address..................0x806aa000
            End   Address..................0x81000000

      Copyright (c) 1982, 1986, 1989, 1991, 1993
        The Regents of the University of California.  All rights reserved.

    Initializing...

      0.06 GT-48304-B-0 (v2.00)

      0.00 GT-48360-L-2 (v2.00)

      1.01 GT-48360-L-2 (v2.00)

      2.02 GT-48360-L-2 (v2.00)

      3.03 GT-48360-L-2 (v2.00)

      4.04 GT-48360-L-2 (v2.00)

      5.05 GT-48360-L-2 (v2.00)

      6.06 GT-48360-L-2 (v2.00)

      7.07 GT-48360-L-2 (v2.00)

      8.08 GT-48360-L-2 (v2.00)

      9.09 GT-48360-L-2 (v2.00)

      10.10 GT-48360-L-2 (v2.00)

      11.11 GT-48360-L-2 (v2.00)


    System Interface Attachments:

      Device tty0 has been attached.
      Device de0 has been attached.
      Device nd0 has been attached.



    System Initialization Completed....


    [2J[1;1HAuthorized use only.


    Unauthorized or improper use of this system may result in administrative

    disciplinary action as well as civil and criminal penalties. By using this

    system you indicate your awareness of and consent to these terms and

    conditions of use.


    Enter password: ****

  • md12345

    4 Posts

    1399

    0

    Posted March 10th, 2011 16:00

    ,Thanks,

    The problem ended up being that I had the terminal emulation in hyper terminal set to Auto instead of VT100 Seems like once enough text came down hyperterminal figured out that it was VT100 in time to change the boot mode, but not at the very start of power up.

    Also, note that the X needs to be an uppercase X when prompted.

     

  • MEG_77

    1 Message

    1400

    0

    Posted September 20th, 2011 08:00

    Rodger,

    Does this procedure also apply to the Powerconnect 3548P? if not, do you know what action I need to take to reset the password on a 3548P

    Thanks for your help.

  • prommu123

    5 Posts

    1400

    0

    Posted November 17th, 2011 22:00

    Hey Rodger,

    Can you please help to recover password on my Dell 6248 Switch. I am very new to operate and troubleshoot Dell Switches.

    Thanks in advance.:emotion-2:

  • JSWhicker

    31 Posts

    1400

    0

    Posted November 18th, 2011 13:00

    Which passwords are you all trying to reset on the Powerconnect 3500's and the 6200? If it is the telnet/web interface password then the user account will need to be deleted and recreated through the console port on the back. If it's the enable password, Then one would need to access the boot menu on both switches to bypass the enable password.

  • prommu123

    5 Posts

    1400

    0

    Posted November 21st, 2011 00:00

    Thanks for your response,  I have a Dell 6248 Powerconnect Switch in my network, but I dont have any credentials to Telent /Webinterface access to the switch. As you said, I need to delete user account by connect console. Can you please give me the steps of delete/create account and how to connect console also.

  • JSWhicker

    31 Posts

    1400

    0

    Posted November 21st, 2011 07:00

    First we would need to connect to thje switch via the console port and use a VT100 Emulator (putty.exe, teraterm pro hyper term etc.) Then run the following commands to create a user account.

    Console>en

    Console#config

    Console(config)#username password level 15

    Console(config)#exit

    Console#copy run start

    This would create an account that can be used to access the web interface and or telnet into the management of the switch.

  • prommu123

    5 Posts

    481

    0

    Posted November 21st, 2011 20:00

    Hey J S Whicker,

    Just to remember you... I dont have even console password to access the switch?

    Does the switch accessible through console without password?

    Or else, we need to break console password too? Pl help with the steps...