UNSOLVED

user_d2d128

updated

3 months ago

U

user_d2d128

1 Rookie

•

1 Message

•

2 Points

0

962

November 20th, 2025 06:59

U2725QE, M2T102, auto brightness dims to 3%

Hello I just bought 2 monitors U2725QE (4K). Both of them connected to one laptop with Thunderbolt cable. Also tried to connect with two thunderbolt cables from one laptop. Updated latest firmware: M2T102. 

Issues I noticed with auto brightness functionality is that: 

1. In the morning (my monitors are standing on a work desk in front of the window) with auto brightness - ON ; Auto Brightness Range level: High , and its automatically goes to: 
Brightness 3 %
Contrast: 75% 

Sitting longer hours I feel that it's to dark and eyes getting tired. At mid-day time brightness increasing but basically from the 16:00  as it's getting dark it's going again back to 3%. So I need to turn Light on and then situation is better. 

As monitor has 3 auto brightness levels (Low ; Mid ; High) is it not possible to make better range for auto brightness.  At Day time on Low - Mid it's always basically 3% , on High Brightness Increasing ~30% similar with LED light on in the room above the curtains. 

What's the purpose of Low and Mid then ? 

2. On my personal laptop I have Dell application installed and one of the monitor is set to Primary monitor for sync and sometimes the pop up appearing with information that secondary monitor is adjusting brightness. But that pop up appears repeatedly as soon as primary monitor auto brightness changes. That's annoying is it possible to turn off the notification ? 

3. On my work PC I don't have dell application installed. But I use the same settings. Without dell application seems like primary sync function for auto brightness is not working. As if primary auto brightness increases  the secondary monitor remains the same. Does auto brightness synch works without dell application ? (Due to policy I can't install dell app on work PC.). 










(edited)

  • DELL-ChrisM2

    Community Manager

    •

    2001 Posts

    •

    10026 Points

    0

    0

    Posted February 28th, 2026 20:36

    @Naveenk.c​ 

    Click the blue "Get Help Now" on the right to start a private live chat session. Share with them the private Service Tag, issues, this thread link, and all of your troubleshooting. This will in turn generate a unique Technical Support case for your unique Service Tag.

    Until a new firmware is released to the U2725QE/U3225QE drivers page to test, the only workaround is to enter the Menu OSD - Brightness/Contrast and turn Auto Brightness Off.

     

    #IWork4Dell

  • javispedro

    1 Rookie

    •

    5 Posts

    1

    0

    Posted November 21st, 2025 20:11

    I have similar requests with dual U2725QE.  

    1) In even reasonably bright room the auto brightness "high" value averages 7% (with M2T101) / 13% (with M2T102). I have to shine approximately 3000 lumens right into the sensor so as to make auto brightness 80%. While I myself find the M2T102 setting agreeable, I think "low" / "med" are useless.  This may be a personal preference, though. 

    2) With multi-monitor sync on, every single time that there's any type of change in luminosity (e.g. a colleague from work passes by and his shadow partially obscures the sensor ) there 's going to be a "Multi-Monitor Adjustment..." OSD message in the secondary monitor showing up for at least 10 seconds. During this time the monitor menu cannot be accessed, either. This is highly annoying and there is no way to disable this (useless) message that I can find. 

    3) Without the Dell Application, Multi-Monitor Sync only works when both monitors are connected with MST (either DP-MST or TB-MST). But if they're connected via "pure" TB, it doesn't work at all. This limitation however is described in the manual. 

    Is there a way to pass at least request (2) to the firmware development team?  This is not a hw failure, it's a firmware enhancement request. 

    (edited)

  • Krazana

    1 Rookie

    •

    3 Posts

    •

    2 Points

    1

    0

    Posted November 25th, 2025 16:08

    I can confirm this issue. I updated my U2725QE to M2T102 and the auto-brightness now aggressively dims to 3% in a standard lit room. It is unusable compared to the previous firmware. Please prioritize a fix

  • Krazana

    1 Rookie

    •

    3 Posts

    •

    2 Points

    1

    0

    Posted November 25th, 2025 16:09

    on previous firmware version it was working fine. 

  • Dbprest

    1 Rookie

    •

    2 Posts

    1

    1

    Posted December 17th, 2025 18:04

    Same, upgraded to avoid the flicker, now with auto brightness on, it never adusts above 3%, no matter the range level set, unless I shine a flashlight on the sensor. My office isn't bright, but it's right by a window and I need the screen brighter. At least with the flicker it was at a usable level otherwise. 

  • Quickben

    1 Rookie

    •

    1 Message

    •

    2 Points

    1

    0

    Posted January 25th, 2026 10:56

    I have a same issue. auto brightness was working fine on stock firmware. After I updated to M2T102, A01 firmware version, it gets too dim in a well lit room (3-5%), unless you shine a flashlight into the sensor, it stays very dim. Pls release a new firmware fix

  • DELL-ChrisM2

    Community Manager

    •

    2001 Posts

    •

    10026 Points

    0

    0

    Posted February 19th, 2026 14:09

    The only way the Dislays team will be aware of the M2T102 auto brightness issue is by the number of support cases created.

    Click the blue "Get Help Now" on the right to start a private live chat session. Share with them the private U2725QE Service Tag, the issue with firmware M2T102, this thread link, and all of your troubleshooting. This will in turn generate a unique Technical Support case for your unique Service Tag.

     

    #IWork4Dell

  • Naveenk.c

    1 Rookie

    •

    1 Message

    •

    2 Points

    1

    0

    Posted February 28th, 2026 08:01

    Same is the case with my new U3225QE Monitor. Disappointing feature.

  • Krazana

    1 Rookie

    •

    3 Posts

    •

    2 Points

    1

    0

    Posted March 9th, 2026 08:35

    @DELL-ChrisM2​ 

    I have been talking with the support now for over 2 weeks now without avail

  • Keepps

    1 Rookie

    •

    1 Message

    •

    2 Points

    2

    0

    Posted March 9th, 2026 12:11

    Yeah, tech support just tells you to download the firmware update and then reset to factory settings. Which works for a day then stops working again.  

    They need a real firmware fix.