UNSOLVED

KKarl

updated

18 years ago

K

KKarl

60 Posts

0

13165

October 28th, 2008 20:00

XPS730H2C New MOBO + Processor (QX9650) but now not Overclocked

Hi All

 

Dell engineers have replaced the MOBO and Processor (QX9650) in my XPS730H2C after some overheating problems (see below for details). Machine is running OK now but BIOS, NVIDIA System Monitor and NVIDIA Control Panel all now show the processor speed to be 3.00 GHz. This machine was overclocked to 3.67GHz at the factory when I bought it but these settings suggest that it's reverted to the base processor speed. I'm going to contact Dell support but in the meantime does anyone here know which settings I need to change in the BIOS and to what values they should be set to return my machine to the factory overclocked state?

 

Many thanks in advance for your help.

 

For those of you interested in the whole sorry tale:

 

I've just had a fortnight of frustration after my XPS730H2C died. It all started when the cooling fans went ballistic (sounding like a Harrier Jump Jet taking off) followed by the machine shutting down completely. Further attempts to start up after a cool down period would result in the machine coming up for a few minutes before the fans would ramp up again and it would shut down. Dell support talked me through some troubleshooting steps to no avail and an engineer was booked to come out and replace the power supply and the MOBO. After the usual problems with cancelled appointments, wrong parts, etc, the engineer fitted the new parts but they didn't help. The engineer and me thought it was most likely a processor overheating issue so he attempted to order a new processor and H2C system but Dell call centre would only agree to a new processor. A new processor was ordered and fitted the next day but this didn't help either so a new H2C was ordered. The engineer came a couple of days later but had the wrong H2C system! Another day and the correct H2C system later the machine is back up and running again. So, I paid for XPS Premium support when I bough my machine but this hasn't been a "Premium" service experience for me. I've taken days off work, had those appointments cancelled, been told that engineers can't be booked for AM or PM; just between 9am & 5pm and it's taken two weeks to get things sorted and I still have a machine that's not configured correctly.

  • hbk123

    2 Intern

    •

    313 Posts

    599

    1

    Posted October 28th, 2008 21:00

    XPS 730 Factory Default CPU and Memory Settings
    These settings will automatically overvoltage the parts as necessary, so no overvoltaging steps are needed to achieve the factory default settings.

    * Restart the PC and enter the Bios Setup
    * Go to Advanced- CPU Configuration [press Enter]
    * Set CPU Multiplier to 9 (for QX9770, CPU-Z shows this as 9.5) or 10 (for QX9650)
    * Set CPU N/2 Ratio to Enabled
    * Set C1E Function to Disabled
    * Set Executive Disable Bit to Enabled
    * Set Virtualization to Enabled
    * Set SpeedStep to Disabled
    * Press Escape
    * Go to Advanced- Overclock Configuration [press Enter]
    * Set EPP 2.0 Memory to Auto
    * Set FSB - Memory Clock Mode to Auto
    * Press Escape
    * Right arrow to Exit
    * Press Exit
    * Press Yes to Save to CMOS and Exit [press Enter]
    Taken from http://www.dellcommunity.com/supportforums/board/message?board.id=Tech_Talk_XPS&thread.id=55109
  • KKarl

    60 Posts

    599

    1

    Posted October 28th, 2008 21:00

    Thanks hbk123.

     

    I did see this entry but wasn't convinced it was specific enough to my system as it just says XPS 730 Factory Default with no reference to if it's H2C, the processor or the final GHz. Anyone out there with the same system as mine (QX9650 Factory Overclocked to 3.67GHz) that can check and post their BIOS settings?

  • Aurora51

    1 Rookie

    •

    139 Posts

    599

    1

    Posted October 28th, 2008 23:00

    KKarl,

     

    This is changed to reflect my current settings: 

     

    * Restart the PC and enter the Bios Setup
    * Go to Advanced- CPU Configuration [press Enter]
    * Set CPU Multiplier to 11x

    * Set CPU N/2 Ratio to Disabled
    * Set C1E Function to Enabled

    * Set Executive Disable Bit to Enabled
    * Set Virtualization to Enabled
    * Set SpeedStep to Disabled
    * Press Escape
    * Go to Advanced- Overclock Configuration [press Enter]
    * Set EPP 2.0 Memory setting CPU OC 0% - current value Enabled

    * Set FSB - Memory Clock Mode to Auto
    * Press Escape
    * Right arrow to Exit
    * Press Exit
    * Press Yes to Save to CMOS and Exit [press Enter]

  • KKarl

    60 Posts

    599

    1

    Posted October 29th, 2008 07:00

    Thanks Aurora51; much appreciated.

     

    I'm waiting on a call back from @ Dell senior support tech so I'll wait for their advice and see how it compares to your settings; should be interesting.

  • KKarl

    60 Posts

    599

    0

    Posted October 29th, 2008 12:00

    Hi

     

    Dell support called me about an hour ago and took control of my machine :smileysurprised:. After digging around for a while they talked me through upping the CPU Multiplier in the BIOS; first to 10x and then to 11x. Things seem pretty stable at the moment @ 3.66GHz so fingers crossed it will remain so. The guy on the phone was polite and understanding but admitted he had only done one other overclocking support call before, which didn't exactly fill me with confidence but we got there in the end.

     

    My only worry is that presumably components are identified as suitable for OCing at the factory when Dell sells OCd systems, so I guess that the MOBO and CPU I have now may not be "certified" as suitable for OCing. I suppose only time will tell. 

     

    Thanks for your support.