UNSOLVED

rhazzon

updated

18 years ago

R

rhazzon

12 Posts

0

168349

October 14th, 2007 14:00

Vostro 200 freezes after XP Splash Screen

I just installed two Vostro 200 PC's with Windows XP Home for a client.  Both machines were running perfectly and were rebooted several times during the install without incident.  When they tried to turn the machines on the next day, they both completed POST and the Windows XP Home splash screen started.  Both machines then went to a black screen and remained there without completing the boot cycle.  No matter what I did I could not get these machines to boot.  Fortunately I did get them both to boot into Safe Mode.  I tried a System Restore, but that did not help.  I was forced to perform a Windows XP repair installation.  Once this was completed both machines booted normally.  They were turned off later that day and when they were turned on the next morning the black screen came up once again.
 
I'm at a complete loss here!  Dell has no idea what the problem is. I find it hard to believe that if both machines are experiencing this problem, that no other owners of these machines aren't experiencing similar problems.  I've dedicated five time the amount of time it should have taken to install these machines in a small office environment.  I feel awful that the client is stuck with $1500.00 worth of doorstops, but there isn't much else I can do.
 
If anyone is experiencing similar problems or has any idea how it might be resolved please let me know.  I'm losing a fortune with this customer, but cannot (in good conscience) walk away until everything is running correctly.
 
Thanks to all!
  • rhazzon

    12 Posts

    763

    0

    Posted October 14th, 2007 14:00

    These systems are turned off each night.  The fact that a repair install works every time is also odd and leads me to believe it is not a power issue.  Like I said, the Starting Windows XP splash screen appears and then it goes blank.  I'm about at wits end and ready to have Dell take these machines back.
  • PETER345

    1 Rookie

    •

    5796 Posts

    763

    0

    Posted October 14th, 2007 14:00

    Yes, it is all very odd. Either they are doing something to the machines to make them fail or something else (either software or hardware) is causing the problems. If they are not doing it, and it happens when the machines are not running, then somehow the disks are getting corrupted. It is almost like the HDs can't store data over night.

    Replacing them is a pain, but might be the best route. I presume they have other working computers in the same environment.

    The only reason for suggesting power, is clearly the two machines have the same failure mode and it is not random.

    Peter
  • rhazzon

    12 Posts

    763

    0

    Posted October 14th, 2007 14:00

    These machines are only a week old.  This happened the day after they were taken out of the box.  The business is brand new and only has one laptop in the office right now.  Thankfully that one works fine.  I'm a bit disappointed in Dell's quality control (or lack thereof) and tech support is of very little help.  I've recommended Dell to clients for many years, but if this is the direction Dell is taking then I may have to look at another manufacturer.
  • PETER345

    1 Rookie

    •

    5796 Posts

    763

    0

    Posted October 14th, 2007 14:00

    You should be able to get Dell to replace them if they are less than 20 days old.

    I presume you have run the diagnostics to check for hardware issues. Of course, it is unlikely that both would have the same hardware problem.

    I also presume you have reseated everything to make sure nothing is loose inside.

    It is strange that the seem to degrade over night. Is it possible they have some sort of power glitches there? Do the "degrade" if not connected to any power source?

    Good luck,
    Peter
  • PETER345

    1 Rookie

    •

    5796 Posts

    763

    0

    Posted October 14th, 2007 15:00

    I have been buying Dells for about 5 years and not had many problems with them. The biggest was a optical drive in a laptop that was flaky. A few problems were related to new Windows XP that resolved themselves when SP1 came out.

    However, getting two machines that don't work is far from satisfying.

    Since safe mode works, have you tried updating the drivers? It is hard to imagine why the drivers would work fine at the end of the day but not at the beginning.

    Have you checked for a BIOS update?

    Maybe they are doing some kind of automatic update that is screwing things up.

    Peter
  • rhazzon

    12 Posts

    763

    0

    Posted October 14th, 2007 18:00

    Odd part is that I went to the Microsoft Update site and applied all available updates.  The machine was then rebooted and everything worked fine.  next day it was a no go.  No BIOS updates available - already checked.
  • timthumb

    74 Posts

    763

    0

    Posted October 15th, 2007 20:00

    Are there any external USB drives plugged into them?  I had to change the boot order in the BIOS because my 200 was factory set to give external drives priority in the boot sequence, which would cause my computer to freeze at that point in the boot process.


    Message Edited by danimal1968 on 10-15-2007 05:07 PM
  • rhazzon

    12 Posts

    763

    0

    Posted October 15th, 2007 22:00

    I think you may have missed the point here.  The XP splash screen appears so it is finding the boot drive just fine.  And safe mode also boots fine.  Which leads me to believe there may be a driver conflict somewhere.  The odd part is that I did all the Windows updates manually and rebooted the PC's several times.  Something happened overnight to both machines that caused this problem.  I did a repair installation of XP and it happened again the next night. 
     
    My idea is that there is an update that is causing this issue.  Since these systems are fairly basic Vostro 200's I can't believe I'm the only one having this problem.  I'm looking for other users of the Vostro 200 that are experiencing similar problems.
  • contactmo

    1 Message

    763

    0

    Posted October 24th, 2007 14:00

    I have the exact same issue.
    I have found that if iIremove all USB cables and fool around with them and plug them into the front ports and mix them all around for some reason it will then start. however the next day the problem returns.
     
    my system is less than a week old.
     
    any ideas? This is pretty bad if dell hasn't addressed this issue yet.
  • PETER345

    1 Rookie

    •

    5796 Posts

    351

    0

    Posted October 24th, 2007 15:00

    Did anyone try resetting the CMOS settings? That can sometimes help with USB issues.

    Peter