
UNSOLVED
Precision 330...
I have a Dell Precision 330 from 2001 with Windows 2001. I'm not sure this error is a BIOS-related error...
The problem was first the bluescreen, " INACCESSIBLE_BOOT_DEVICE".
I tried to solve this error. I bought the new internal SCSI-drive.
But in this process, I changed the settings in BIOS. Now, the little diod on the monitor doesn't change from orange to green...! I searched and tried to reset the BIOS. I took out the battery as well as removing the jumper next to the battery, named "PSWD"...
***
After iunstalling Windows on a different drive the other day, I should install the drivers for the wireless network (D-Link). But the manual for the wireless network reads, install the drivers FIRST and insert the PCI-card AFTER. So.... I uninstalled the software, turned of the computer, removed the PCI-card... then tried to start the computer to install the drivers first.
But this never worked. The computer never started again... And here I am. With Windows 2000 in the cd-drive and a blank 73 GB new SCSI drive in the case...
Still, not even an error message!!
Responses (9)
Solutions (0)
- I'll give you a post to reply to! :-)
I'm an old Mac-dude... so all this SCSI-talk is very familliar with me.
My wonder is, when inserting the powersupply, why doesn't the computer start, to look for a OS on any drive... or if not finding any, report an error. "OS not found."
I have also tried to reset the memory by removing the battery and also removing the jumper next to the battery. Why is this feature working so bad!? It works sometimes... but mostly not!?
Maybe my computer is broken... then, if so, why does it sometimes work with no greater errors...!?
****I forgot to write. This error showed earler yesterday: "Alert! Previous voltage failure!"
Yesterday, I manage to do many things such as running the advanced defrag software on all drives. Also the external. one USB2, one FireWire. - Sorry for the slow reply here... Sometimes the computer actually work so i was thinking of being carefull with posts in this forum. However, the startup-process is uncomfortable dynamic...
In this current set-up, there are three scsi drives in the computer. (It's ONE computer. My appology for bad writing...)
I manage to install and update everything to the new 74 GB drive, as I made in the 20 GB partition. (How do I get the rest of the drive...!?) A blank copy of windows is quite neat! I installed other things such as the Canon printer as well as some software.
The computer seemed to work fine with me. But I only had the new drive in place. The others were not connected at this time. I made many re-boots, turning off and on the computer. But... When trying to connect these two other drives we're back in square one!!
****The symptom is; the small diod on the monitor remains orange. It normally turns into green and the first things in the computer starts to load. However, sometimes the computer needs to rest with the cord in place, and the electricity running in the curcuits... after resting for about 10-15 (or even 8) minutes, the computer is loading the software!!! (And later windows.)
The SCSI ID's is a little tricky. The three drives looks very much alike (68 pins drives). But the ID instructions on this last drive was the pins on the back. Between the SCSI socket and the power socket.
The back of the drive:
[SCSI socket] -- [+5][NC]:emotion-29:[4][2][1] -- [powersocket]
****I have no idea about +5 (or +S ..??) or NC. For those of you not familliar with the SCSI pins, let's just say, by putting jumpers on these pins, it's possible to reach all numbers from 0-15 = 16 different ID's.
The new drive and one of the old once are Fujitsy while as the last drive is IBM. I believe the IBM-drive was the original, shipping drive... but in this, I may be wrong. - There's another thread going about adding scsi drives. You may want to check that out. The mac scsi world is like anything in the pc worls, so much simpler as there are so few choices. 25 pin, 50 pin, 68 pin or 80 pin. SE LVD or HVD. Check your drives to make sure they are all using the same format as the controller. You may have to add a controller or replace a drive. I like setting to SE for all internal drives as the LVD and HVD are designed to handle longer runs
- Thank you for the reply! I took the time to read this other thread. It seems to be similar, but not the same.
I was not aware of SE, LVD or HVD and I shall investigate in this.
Howerver, my drives are identical with 68 pins. Else, the SCSI connector wouldn't fit...
I'm also used to the termination and I know it's important... But it's all sitting there, as the factory setting. (My computer was ordered and shipped with SCSI back in 2001.)
In this moment, my problem isn't really the drives. My problem now is that the computer boots at random! Really, I don't know the word... not really boot, because that is reading from the harddrives... Before that step, when the DELL logo is shown and the BIOS version is shown. This part of the "booting procedure". It works at random. - Follow-up:
I bought the new battery, thinking the one I have might been flat.
However, no dirfference in performance... The DELL startup screen still doen't show. The screen witht the logo and the BIOS version.... The diod on the screen is still orange, never turns green. (No signal is brought to the screen.)
"It's easy when you know how" ... and in this moment, I'm little disapointed... :-(

tr4
1 Rookie
•
1727 Posts
435
0
Posted March 5th, 2008 12:00
What was the model of the old drive and the new one? What jumpers are set on each. When you power on the pc, do you get anything or is it always blank?