
UNSOLVED
Optiplex 7010 SFF no POST when network adapter in PCI-E x4 slot
Hello,
Just as the title suggests, my machine refuses to POST when I install a tp link TL-WDN4800 wireless apapter on the "wire x4" PCI-E slot (the bottom one according to the manual). If I install the adapter in the top slot, everything works fine.
Can anybody help?
more details: The machine doesn't make any beep sounds when trying to boot, and no video comes up. Can only restart by holding power button down for some seconds....
1 person also has this problem
Responses (13)
Solutions (0)
DELL-Chris M
Community Manager
•
56891 Posts
•
232143 Points
4709
0
Posted April 1st, 2013 19:00
It appears that not having the PCIe x16 video card installed is making the system think the wifi card in the x4 slot is video. Other users will have to test the 7010 with only an x4 card installed to verify this.
DELL-Chris M (old account)
#IWork4Dell
Hi,
I just received my graphics card (HD 7750).
I proceeded to install the graphics card in the x16 top slot and the WLAN card in the x4 slot (bottom). The system shows the same behaviour as before, it won't boot.
If I switch the cards around, everything works fine.
This is obviously not working as intended, since my graphics card is now crippled to a PCI-E 2.0 x4 slot ....
nick2paris
1 Message
4714
0
Posted December 7th, 2013 04:00
Hi,
I have the same problem, can you reply to DAN0512 ?
I have a wifi card, TP-Link TL-WDN4800, in the brown slot (pcie x4) and my optiplex don't boot.
If I put it in the blue slot (pcie x16), all is ok.
I need to install 2 cards, wifi (in x4 slot) and graphic (in x16 slot) ...
I thought it was possible ...
akocaturk52
1 Message
4714
0
Posted March 16th, 2016 15:00
Hello,
I recently purchased a TL-WDN4800 and tried to install it in my Optiplex 7010 mid tower, with the same issues described above. No POST, monitor does not turn on, HDD light blinks once and then stays off while fans spin.
I found that the card works in SLOT1, the blue one which I normally use for my graphics card, and SLOT2, an x1 slot that is normally covered by my graphics card's heatsink. SLOT4, the PCIe "wire x4" slot, does not work.
The card worked just fine in the x4 slot of a Precision 390 I had, so it suggests that the card is alright. But I find it a mighty coincidence that searching for "Optiplex 7010 Slot 4 no POST" only brings up this thread with people having the exact same hardware.
I'm going to try playing around with my BIOS settings to see if that straightens this out, but I'm here to say that this problem isn't isolated, and if anybody's figured out a solution in the past three years, I'd like to know how you fixed it.
--AK
hellspawn9999
2 Posts
4714
0
Posted September 13th, 2016 16:00
Same issue here. Any solutions? Will upgrading the BIOS do the trick?
hi,
same problem: I had TP-Link TL-WN881ND installed in slot 4 and it worked fine.
the TL-WDN4800 does work in slots 1 and 2, but when it is in slot 4 PC won't POST.
updating BIOS to last version (A24) does not help. why this trap?
I have slots 1 and 2 blocked by graphic card so I sorted it out by buying PCI-Express PCI-E x1 Riser cable and leading PCI-E 2 around, but it looses some of adaptors signal strenght and the TL-WDN4800 hangs unprofesionally mounted down the case...
--ziki
The 390 does not have PCI-E 3.0 slots. There is an inherent incompatibility with PCI-E 3.0 and older versions of cards. This is because the power profile AND the clock speed of the bus does not DOWNGRADE to 1.0 or 2.0 speed. If you need 802.11 Dual band use a USB Wifi Adapter like the
EIDEMAX AC600 usb adapter.

DELL-Chris M
Community Manager
•
56891 Posts
•
232143 Points
4709
0
Posted April 1st, 2013 08:00
Dan0512,
So the system is thinking that the wifi card is a video card when in the #16 PCIe x4 slot 2. Is there a PCIe x16 video card in the #17 slot 1?

DELL-Chris M (old account)
#IWork4Dell