
UNSOLVED
D
Dan_Honemann
45 Posts
0
5411
December 27th, 2005 11:00
Firewire card won't connect to external drives in 8250
I'm in the midst of a total re-installation of my 8250 (with a replacement motherboard) and have managed to get Windows XP Home, all Dell drivers, and all my PC Cards (ATI Radeon 9700 PRO, Adaptec 2906 SCSI, Promise Ultra 133 TX2 controller, generic OHCI-compliant IEEE 1394 firewire) installed. I've also installed a couple USB hubs, wacom tablet and two printers. I've run all windows updates.
It took me a long time to get the Adaptec SCSI card working (first PCI card I installed), and I finally had to reset the BIOS by entering system setup (F2), turning on caps lock, scroll lock and num lock, pressing Alt-E, then Alt-F, then saving the default settings and restarting, then putting the scsi card in PCI slot 1 and letting windows find it.
I also had no luck with the Promise controller when I tried it at first in PCI slot 3; moving it to PCI slot 2 (next to the Adaptec card) worked, however.
I put the firewire card in PCI slot 4 and windows xp recognized it fine; Device Manager has an entry for it under "IEEE 1394 Bus host controllers" as "NEC OHCI Compliant IEEE 1394 Host Controller" (Microsoft driver version 5.1.2535.0 (7/1/2001)).
The trouble is, whenever I plug in any external firewire drive, nothing happens. I have tried everything I can think of to get this to work: reseating the card to PCI slot 3; doing the BIOS reset trick; trying different external firewire drives (I have several, and different brands); scanning for hardware changes in Device Manager; un-installing the device then scanning for hardware changes and letting it find the card again; etc.
What's odd is that this is the SAME firewire card and drives that were working FINE before my re-install. With the card in slot 4, it only shares its IRQ (19) with two VIA USB controllers (one enhanced)--which shouldn't be a problem (all my devices are on shared IRQ's in any event; it shared IRQ 18 with the network controller and two usb controllers when it was in slot 3 and still no luck; system information reports no IRQ conflicts in either case).
I would think it must be something in Windows but when I boot to an Acronis True Image CD (a Linux-based booter), it doesn't see the firewire drive attached to the card either.
And yet if it is a hardware problem, it seems odd that Windows recognizes and installs the card fine, and Device Manager shows no problems. Event Viewer logs no errors.
So far I am 0 for 3 trying to install any PC cards in PCI slots 3 or 4 on this replacement motherboard.
What am I missing? Is there a way to test the PCI slots or the firewire card?
Thanks,
Dan
It took me a long time to get the Adaptec SCSI card working (first PCI card I installed), and I finally had to reset the BIOS by entering system setup (F2), turning on caps lock, scroll lock and num lock, pressing Alt-E, then Alt-F, then saving the default settings and restarting, then putting the scsi card in PCI slot 1 and letting windows find it.
I also had no luck with the Promise controller when I tried it at first in PCI slot 3; moving it to PCI slot 2 (next to the Adaptec card) worked, however.
I put the firewire card in PCI slot 4 and windows xp recognized it fine; Device Manager has an entry for it under "IEEE 1394 Bus host controllers" as "NEC OHCI Compliant IEEE 1394 Host Controller" (Microsoft driver version 5.1.2535.0 (7/1/2001)).
The trouble is, whenever I plug in any external firewire drive, nothing happens. I have tried everything I can think of to get this to work: reseating the card to PCI slot 3; doing the BIOS reset trick; trying different external firewire drives (I have several, and different brands); scanning for hardware changes in Device Manager; un-installing the device then scanning for hardware changes and letting it find the card again; etc.
What's odd is that this is the SAME firewire card and drives that were working FINE before my re-install. With the card in slot 4, it only shares its IRQ (19) with two VIA USB controllers (one enhanced)--which shouldn't be a problem (all my devices are on shared IRQ's in any event; it shared IRQ 18 with the network controller and two usb controllers when it was in slot 3 and still no luck; system information reports no IRQ conflicts in either case).
I would think it must be something in Windows but when I boot to an Acronis True Image CD (a Linux-based booter), it doesn't see the firewire drive attached to the card either.
And yet if it is a hardware problem, it seems odd that Windows recognizes and installs the card fine, and Device Manager shows no problems. Event Viewer logs no errors.
So far I am 0 for 3 trying to install any PC cards in PCI slots 3 or 4 on this replacement motherboard.
What am I missing? Is there a way to test the PCI slots or the firewire card?
Thanks,
Dan
Responses (2)
Solutions (0)
Dan_Honemann
45 Posts
178
0
Posted December 27th, 2005 13:00
The firewire card is a Koutech PCI to 1394a Card Model IO-PFW310 found here:
http://www.koutech.com/proddetail.asp?linenumber=75
The box just says I/O Future FireWire/IEEE1394 3-Port PCI Host Controller (I bought it from newegg.com). The Koutech website (as well as the manual that came with the card) state that Windows XP has the latest drivers for this card built-in. And in fact I *did* have the card working with my firewire drives before my latest re-install of windows, so I am fairly certain this isn't a driver issue.
Thanks,
Dan

HTT Good HT Bad
2 Intern
•
1275 Posts
178
0
Posted December 27th, 2005 12:00