UNSOLVED

stealthgeek

updated

20 years ago

S

stealthgeek

1 Rookie

•

63 Posts

0

12316

September 14th, 2006 04:00

Dell7900GTX getting hot in SLI....Help

Just upgraded from a single 7900GTX to Dual 7900GTX (both exact same DELL cards).  FPS did increase but so did the temp. I'm running right at the threshold of overheating (high in the yellow section on the temp indicator).  I noticed when I installed the second card it pretty much completely blocks the intake on the primary card, while the second cards intake is clear.  The primary card is getting hot while the secondary card is not.  I know something is wrong and I was hoping someone could help me make sense of this.  Just spent a bunch of money to upgrade to dual SLI and the reward is I can't tell the difference during gameplay (only game played is FEAR so far) and now I have overheating issues.....NOT COOL :smileysad:
Thanks
 
Oh yea, forgot to mention, I'm running this on my brand new XPS700 with a Core2 E6700
No over-clocking, latest drivers from Nvidia (91.47), 2007wfp monitor, pretty much all default settings in the Nvidia Control Panel other than enabling SLI.

Message Edited by stealthgeek on 09-14-200612:23 AM

Message Edited by stealthgeek on 09-14-200612:26 AM

Message Edited by stealthgeek on 09-14-200612:27 AM

Message Edited by stealthgeek on 09-14-200612:59 AM

  • Aivas47a

    1227 Posts

    359

    0

    Posted September 14th, 2006 05:00

    Don't fear the yellow, extreme heat (especially for the upper card in SLI) is par for the course.  Load temps in the high 70s or low 80s (centigrade!) don't seem to do any damage.  And there's really not much you can do about it, short of some radical case modding or VGA card water cooling which is just not going to be practical, especially with the XPS700 case.  You'll notice if you go into the Nvidia control panel the default core slowdown temp is 110C.

    Message Edited by Aivas47a on 09-14-200601:05 AM

  • tphillips63

    4 Apprentice

    •

    2629 Posts

    •

    7922 Points

    359

    0

    Posted September 14th, 2006 15:00

    This is correct, did you notice in the temps section where it ays it will shutdown due to too high temps? It is like 120C.
    Yellow does not mean it is a problem or even getting close. You have to be in the red and way up there for it to be a problem.
    TYh erest of your concerns are just the way it is.Thereis no other way for it to work and the heatsinks are just about the best you can get and they come with it so I would not even go with afermarket coolers unless you just want to.
    You could water cool them but thats a pain too.
  • MrAce

    2 Intern

    •

    354 Posts

    359

    0

    Posted September 14th, 2006 18:00

    your temps are fine
  • hojusimpson

    81 Posts

    359

    0

    Posted September 14th, 2006 18:00

    I usually disable SLi for regular use (non-gaming) so that I can use dual monitors and the temperature of the 1st card is around 58C usually. But while gaming (with SLi on of course), the temperature of the 1st card goes to high 70's, low 80's C. The second card does not get too hot, usually about high 50's C. Like others mentioned, the cooldown threshold is 110C so I think if you stay at least 15-20 C below that, you're fine.
  • Aivas47a

    1227 Posts

    359

    0

    Posted September 14th, 2006 20:00



    @MrAce wrote:
    your temps are fine



    Assuming the tower is under your desk, SLI will keep your feet warm during winter gaming too. :smileytongue:
  • tkutchma

    20 Posts

    359

    0

    Posted September 15th, 2006 11:00

     so how do you enable/disable SLI
    .
    and how are you monitoring you temps
    .
    (new user)
  • stealthgeek

    1 Rookie

    •

    63 Posts

    359

    0

    Posted September 15th, 2006 12:00

    Thanks for the responses...guess maybe it is normal, but it still seems pretty darn hot.  Before adding the second card, while playing FEAR, the primary card ran quite cool, never getting in the yellow (80'C plus).  But now that the second card is in place, covering the intake on the primary card, I guess the air flow is not so good...seems like a bad design to me.  I'll just have to keep an eye on it.
     
    tkutchma
    To answer your questions:
    Once second like card is plugged into bus, with SLI jumper and power connection in place, just power up the system.  In the Nvidia Control Panel, found in the System Display Properties > Settings > Advanced (Classic or New Control Panel) you'll find a "Set SLI Configuration" section.   There is where you have to check the box, enabling SLI (default setting is disabled)
    Also, in the Nvidia Control Panel you'll find Temperature Monitoring.  Plus, I just downloaded nTune and found a pretty nice temperature monitoring option there too.
     
    Wow, I just proof read my above paragraph and realized i truly am a geek :smileywink: But that's ok because I love this stuff.
    Thanks again for the help.
  • MrAce

    2 Intern

    •

    354 Posts

    359

    0

    Posted September 15th, 2006 13:00

    Seriously, your temps are fine.