
UNSOLVED
4300 won't start/amber blinking power light
I purchased a Dimension 4300 less than 2 months ago, worked fine until yesterday. One minute the screensaver was on and appeared normal, next time I looked over at the computer the screen was blank. The power light on the front and the hard drive light are flashing amber instead of green, and even w/ a call to tech support nothing we did seemed to help. The computer won't respond to anything, and though looks to be getting power, the cdrom won't even open.
Has anyone come across this before. The guy at Dell Tech Support never even mentioned the Diagnostic lights on the back of the machine last night. What's up w/ that? Three hours of my time wasted unplugging everything, shutting down-powering up, and on hold for nothing. Seems I could have been able to at least narrow it down w/ the diagnostic codes. Do I have a hard drive problem on my hands, a P4 problem, motherboard? Please help if you can. Would be nice to know what direction of look in. Thanks.
Has anyone come across this before. The guy at Dell Tech Support never even mentioned the Diagnostic lights on the back of the machine last night. What's up w/ that? Three hours of my time wasted unplugging everything, shutting down-powering up, and on hold for nothing. Seems I could have been able to at least narrow it down w/ the diagnostic codes. Do I have a hard drive problem on my hands, a P4 problem, motherboard? Please help if you can. Would be nice to know what direction of look in. Thanks.
Responses (7)
Solutions (0)
bturpin111
52 Posts
355
0
Posted November 20th, 2001 21:00
I am no expert but have been messing with PC's for years. I can offer the following:
Power off and remove the power cord. Open the Case. Gently but firmly push the top of the inserted cards to ensure each card is firmly inserted into the slots. Then look and chck that the ribbons to each drive is in place. At this time it wouldn't hurt to also push each fitting to again ensure that the connections are firmly seated. Do the same to the power cables to each of the drives.
After your sure all seems OK plug everything in LEAVING the case open. Press the power button and cross yuor fingers.
It should power up and take off. In the very least with the case open you can see if everything is powering up such as the fan, insernal lights come on and the drives are spinning up. If every thing seems to work and still no video then possibly the video card is bad. If you get power lights and thats it then possibly the CPU went bad.
If non of the above helps and Dells Techs can't assist e-mail me and i will help in any way i can.
BTurpin111@aol.com
Dimension 4300
P4 1.6
512MBburtieburtie
3 Posts
355
0
Posted November 21st, 2001 05:00
Hi,
This seems to be a 4300 problem... I have a 4300 too and I have the same problem... But I didn't receive an answer form Dell tech yet...
If u got a solution, please post it here, maybe I'm faster working again that way.
jscurt wrote:
- I purchased a Dimension 4300 less than 2 months ago,
- worked fine until yesterday. One minute the
- screensaver was on and appeared normal, next time I
- looked over at the computer the screen was blank.
- The power light on the front and the hard drive
- light are flashing amber instead of green, and even
- w/ a call to tech support nothing we did seemed to
- help. The computer won't respond to anything, and
- though looks to be getting power, the cdrom won't
- even open.
-
- Has anyone come across this before. The guy at Dell
- Tech Support never even mentioned the Diagnostic
- lights on the back of the machine last night.
- What's up w/ that? Three hours of my time wasted
- unplugging everything, shutting down-powering up,
- and on hold for nothing. Seems I could have been
- able to at least narrow it down w/ the diagnostic
- codes. Do I have a hard drive problem on my hands,
- a P4 problem, motherboard? Please help if you can.
- Would be nice to know what direction of look in.
- Thanks.
-
-
- Burtie-
I believe I have solved the problem w/ my machine, though not totally convinced it is fixed until it runs for a while without a hitch. Hopefully I won't be like so of the poor saps on this message board who seem to be regretting their purchase.
This is what I learned from this experience: If you are running Windows ME then you have a 'hibernate' & 'standby' mode that are virtually worthless. For some reason WinME likes to lock up in this mode from time to time. The computer will kick into this mode at times unless you shut it off in the control panel "power options" menu. I got the system to clear out of hibernate by powering down, unplugging the power cord from the back of the chassis, powering down completely by holding the power button down for another 5-10 seconds, leaving it sit for an hour or two and starting it back up after plugging everything back together. It took a couple of times doing this to get the system completely back to desktop, and then I was able to get into the control panel. I haven't noticed any lost data or programs that aren't working. I was really afraid the power supply or motherboard were trashed on my brand new system. I hope it's this simple for you too. Good luck.
- I had the same problem, went thru tech, they had me unplug everything until it worked again for a few hours. Called again and a tech showed up at my home and installed a new motherboard. That fixed the problem and it has been working for lasts few weeks. Bottom line, tell them you need a new motherboard.

dre53
396 Posts
355
0
Posted November 20th, 2001 19:00
Dimension XPS B1000 /windows XP (home)
384mb 700 Rdram
60 gig Maxtor HD
Iomega 100 External Zip USB
Promise ATA 100
3Com 10/100 nic card
Gforce II Pro 64 mb Ram
Samsung DVD-ROM SD-612
Sony CD-RW CRX-140E
Santa Cruz Sound Card
Microtex Scanner 3700 USB
Logitech Quickcam Pro 3000 USB
Altec Lansing 885
Hp 1100 Photosmart Printer