UNSOLVED

VincentA1

updated

13 years ago

V

VincentA1

11 Posts

1

190812

November 3rd, 2013 01:00

Alienware X51 USB 3.0 ports run at 2.1/2.0 speed

Alienware X51 R1

Windows 7 64-bit

I have 2 USB 3.0 ports on the back of my desktop but when I plug my USB 3.0 External HDD into one of them, it runs at USB 2.1 speed. When I plug it in, the USB 3.0 Monitor shows a notification on the task bar saying: "This device can perform faster. This USB Mass Storage Device can transfer information faster if you connect it to a Super-Speed USB 3.0 port." I opened USBDeview and looked at the USB version of my External HDD and it is showing USB 2.1. I've already analyzed my system for updates and my drivers are all updated.

  • shesagordie

    12 Elder

    •

    46017 Posts

    3126

    0

    Posted November 3rd, 2013 10:00

    Moving this thread to the Alienware Owners Club Forum.
      
    Bev.

  • 3126

    0

    Posted November 4th, 2013 14:00

    Try upgrading the FW -

    http://www.dell.com/support/troubleshooting/us/en/19/KCS/KcsArticles/ArticleView?c=us&cs=19&docid=439267

  • VincentA1

    11 Posts

    3126

    0

    Posted November 4th, 2013 21:00

    It still says 2.1 for speed in USBDeview and the notification still pops up when I plugged it in.

  • Milena M458

    6 Operator

    •

    2699 Posts

    3126

    0

    Posted November 5th, 2013 07:00

    Hello VincentA! 

    Have you tried different devices 3.0 on that port, to check if it’s the external hdd or if it’s the port the one that is giving you the issue?

  • VincentA1

    11 Posts

    3128

    0

    Posted November 5th, 2013 17:00

    I don't have any other USB 3.0 devices, I could have tried if I had one.

  • Milena M458

    6 Operator

    •

    2699 Posts

    3128

    0

    Posted November 6th, 2013 09:00

    Have you test the external hdd in another computer to check if you facing the same problem?

    As a work around you can uninstall the 3.0 driver and download the latest version from www.support.dell.com

  • VincentA1

    11 Posts

    3128

    0

    Posted November 7th, 2013 23:00

    I haven't tested the external HDD in another computer because I don't have any other computer that has USB 3.0 ports on them. I uninstalled the 3.0 driver and installed the latest version and the same thing pops up.

  • Taomyn

    131 Posts

    3128

    0

    Posted November 8th, 2013 08:00

    Are you definitely using a USB 3.0 cable? They are different, but you can use a 2.0 cable in a 3.0 device which would cause what you're seeing.

    Also are you absolutely sure you're connecting to one of the blue 3.0 ports, as I never see this message unless I accidentally plug my 3.0 USB stick into the wrong one.

  • VincentA1

    11 Posts

    3128

    0

    Posted November 8th, 2013 18:00

    I'm definitely using a USB 3.0 cable and plugging it in to a USB 3.0 port. This is my USB 3.0 ports and this is my USB 3.0 External HDD. My external HDD is a FreeAgent GoFlex Drive 1 TB and with a USB 3.0 Upgrade Cable. Here are some info in USBDeview if it helps.

  • VincentA1

    11 Posts

    1283

    1

    Posted November 10th, 2013 01:00

    I think there is something wrong with my external HDD. My external HDD is connected to the computer and when I try moving files there, it takes awhile (a few minutes) to finish moving that item, even though the progress bar is full. Then, sometimes, it will disconnect even though it's plugged in. I replugged the external HDD to the USB 3.0 and it wouldn't detect it. I plugged the external HDD into a USB 2.0 port and it works fine, no freezing when moving files. When I plugged a USB 2.0 flash drive into the USB 3.0 port, it was detected and working fine. I will try and contact Seagate and see what they can do for me.