UNSOLVED

mencik

updated

7 years ago

M

mencik

4 Posts

0

3447

June 13th, 2019 20:00

Inspiron 5770 Windows 10 - How to make USB look like COM port?

I have a legacy device that connects via USB, but needs to look like a COM port. In Device Manager, Ports (COM and LPT) does not even appear as it did in previous versions of Windows. So, how do I make my USB ports recognize a serial interface over USB? Do I need a new driver? If so, which one and where do I get it?

  • nyc10036

    6 Operator

    •

    5640 Posts

    3053

    0

    Posted June 14th, 2019 06:00


    @mencik wrote:

    I have a legacy device that connects via USB, but needs to look like a COM port. In Device Manager, Ports (COM and LPT) does not even appear as it did in previous versions of Windows. So, how do I make my USB ports recognize a serial interface over USB? Do I need a new driver? If so, which one and where do I get it?


    The driver you need depends on the IC that is in the adapter you are using which we don't know anything about except that you have one. 

     

     

    .

  • mencik

    4 Posts

    3027

    0

    Posted June 22nd, 2019 08:00

    It is a simple USB cable, no adapter. On other computers, like my older HP also running Windows 10 and others running older versions of Windows, there is a section in the device manager for Ports (COM and LPT). On the Inspiron, there is no such section. If that section was there, you can select which COM port a USB device represents. Obviously something is different with the Inspiron as far as how the USB acts, and I suspect a driver is missing. If it is something else, I am open to suggestions.

     

  • nyc10036

    6 Operator

    •

    5640 Posts

    3022

    0

    Posted June 22nd, 2019 09:00


    @mencik wrote:

    It is a simple USB cable, no adapter. 

     


    That makes no sense!

     

  • mencik

    4 Posts

    3009

    0

    Posted June 22nd, 2019 16:00

    You obviously have never dealt with a device that uses the old USB Type B to USB Type A cable for older devices. It communicates with the system as if it were a COM serial port. On many computers you can look in device manager and see Ports (COM & LPT) and you can specify the particular port that a USB interface will look like. On the Inspiron 5770 with latest Windows 10, the Ports (COM & LPT) is not part of device manager, so I can't specify, and my device cannot connect. It does not auto-detect.

  • nyc10036

    6 Operator

    •

    5640 Posts

    3003

    0

    Posted June 22nd, 2019 17:00


    @mencik wrote:

    You obviously have never dealt with a device that uses the old USB Type B to USB Type A cable for older devices. It communicates with the system as if it were a COM serial port. On many computers you can look in device manager and see Ports (COM & LPT) and you can specify the particular port that a USB interface will look like. On the Inspiron 5770 with latest Windows 10, the Ports (COM & LPT) is not part of device manager, so I can't specify, and my device cannot connect. It does not auto-detect.


    ROTFL.

    I haven't have I????

    ROTFL.

     

    I guess you would have to tell my current employer that I am not actually programming for the COM port!

    It is all in my imagination.

     

    Your device needs a Windows 10 driver.

    .

  • U2CAMEB4ME

    6 Operator

    •

    6245 Posts

    2999

    0

    Posted June 22nd, 2019 17:00

    Welcome to the Dell Community  @mencik 

    Power-on and start tapping "f2" to enter BIOS setup.

    See if you have the option to Enable or Disable the Serial Ports.

    Best regards,

    U2

  • Philip_Yip

    11 Legend

    •

    16052 Posts

    •

    65915 Points

    2988

    0

    Posted June 23rd, 2019 01:00

    It depends what USB to Serial Adaptor you have. These ones Plugable USB to RS-232 DB9 Serial Adapter (Prolific PL2303HX Rev D Chipset) have a Driver which Windows 10 obtains directly from Windows Update. Do you have any unknown Devices or any Devices marked with an ! or ? in the Device Manager? If not does the port work on another PC?

     
     

  • speedstep

    11 Legend

    •

    46969 Posts

    2979

    0

    Posted June 23rd, 2019 03:00

    https://docs.microsoft.com/en-us/windows-hardware/drivers/usbcon/usb-driver-installation-based-on-compatible-ids

    The PL-2303HX is a low cost and high performance USB-to-Serial Bridge Controller. Prolific does not make adapters.

    The PL2303 Windows 10 driver can also be downloaded automatically via Windows Update. Just plug-in the PL2303 USB Serial device and Windows Update (Internet connection is required) will download and install the latest drivers.

    NOTE:

    • Windows 10 is NOT supported in PL-2303HXA/XA EOL (End-of-Life) chip versions.
    • Prolific recommends to buy PL-2303HXD (HX Rev D) chip or newer generation chip versions.

    Because this works the chip is often counterfieted. So beware of FAKE PL2403HXD adapters.

    https://www.amazon.com/Plugable-Adapter-Prolific-PL2303HX-Chipset/dp/B00425S1H8

    Windows Driver Installer Setup Program 
    (For PL2303 GC, GS, GT, GL, GE & PL2323 versions)

    http://www.prolific.com.tw/US/ShowProduct.aspx?p_id=225&pcid=41

    USB SERIALUSB SERIAL

     

    Windows 10

    In Windows 10, a new INF, Usbser.inf, has been added to %Systemroot%\Inf that loads Usbser.sys as the function device object (FDO) in the device stack. If your device belongs to the Communications and CDC Control device class, Usbser.sys is loaded automatically.You do not need to write your own INF to reference the driver. The driver is loaded based on a compatible ID match similar to other USB device class drivers included in Windows.

    USB\Class_02

    USB\Class_02&SubClass_02

    Starting in Windows 10, Usbser.sys supports USB Selective Suspend. It allows the attached USB-to-serial device to enter a low power state when not in use, while the system remains in the S0 state. When communication with the device resumes, the device can leave the Suspend state and resume Working state. The feature is disabled by default and can be enabled and configured by setting the IdleUsbSelectiveSuspendPolicy entry under this registry key:

    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\USB\\\Device Parameters

    To configure power management features of Usbser.sys, you can set IdleUsbSelectiveSuspendPolicy to:

    • "0x00000001"

      Enters selective suspend when idle, that is, when there are no active data transfers to or from the device.

    • "0x00000000"

      Enters selective suspend only when there are no open handles to the device.

     

  • JJ123

    1 Message

    1516

    0

    Posted February 3rd, 2021 13:00

    @nyc10036 Why are you being so mean? The fact that you know more than someone about a subject does not mean you have to be rude to them about it.

     

    @mencik good luck friend, sorry I can't help you out here