UNSOLVED

BillClark22

updated

15 years ago

B

BillClark22

15 Posts

0

65339

October 27th, 2010 10:00

Hard drives for PS100E & PS70E

We currently have the above 2 Equallogic SAN's and we are wanting to max them out in terms of storage space.  We are currently using some Western Digital SATA-II drives that are 250GB and only 7.2K.  What is the max hard drive size & access speed these SAN's will accept?  I've done some digging but just can't seem to find that bit of information.  We are currently on v3.2.0 (R59126) for firmware, but are planning on upgrading to the current release soon.  Thanks.

Bill

  • Dev Mgr

    6 Operator

    •

    9308 Posts

    •

    3 Points

    1633

    0

    Posted October 27th, 2010 11:00

    From what I've heard, if you are under warranty and you put in non-certified drives, you void the warranty on the whole system.

    Assuming you're out of warranty, or at planning to buy the drives from Dell, with the latest firmware, Dell offers 2TB, so those should work.

  • BillClark22

    15 Posts

    1633

    0

    Posted October 27th, 2010 14:00

    Is there a document somewhere that will tell me what is certified or not?  The drives currently in the SAN are Western Digital 250GB (WD2500YS-01SHB0), not like they are special or anything.  I sent an email to Dell tech support, guess I'll see what they have to say.

    Bill

  • Dev Mgr

    6 Operator

    •

    9308 Posts

    •

    3 Points

    1634

    0

    Posted October 27th, 2010 17:00

    Only Dell Equallogic drives are certified. You might be able to find Dell Equallogic drives from resellers, but "retail" drives aren't certified no matter which model they are and/or which firmware they have.

  • Joe S586

    9 Technologist

    •

    729 Posts

    1634

    0

    Posted October 28th, 2010 13:00

    I’m Joe and I work for Dell EqualLogic.  The largest capacity disks that were available for the PS50E-PS400E series were the 750GB 7.2K (SATA).  However, upgrade kits that would have enabled you to upgrade an existing array to a larger size capacity are no longer available for purchase, this is due to the End of Service of this series, and service contracts will only be sold/supported with an end date of April 18th 2013.  Installing any other drive that is not purchased through Dell EqualLogic, will in fact void any warranties, support contracts, or technical support on the array.

  • Net-Paws

    3 Posts

    1634

    1

    Posted October 28th, 2010 14:00

    The largest drive sold and tested for PS100 model arrays were 750 GB.  This was marketed as a PS400E and (most of them) shipped with Seagate Model ST3750640NS drives running drive firmware 3.AEG.  2 TB drives have never been tested or sold with that chassis, and will likely have problems

    Checked with sales, and drive upgrade kits are no longer available for that model.

    DEV MGR is correct that "retail" drives aren't certified no matter which model they are and/or which firmware they have, but that also implies loss of support.  Non tested/supported drives may have a higher failure rate, may run hotter (possibly affecting other components), and may even hit data integrity issues.

  • BillClark22

    15 Posts

    1634

    0

    Posted October 28th, 2010 14:00

    So what you are saying is that these units are at their End of Service as far as upgrading and parts, but yet service contracts will still be sold through 2013?  Does that only seem strange to me?  I understand that equipment eventually has to hit the end of servicable life, but I would think parts, etc would be available to the very end.  Is there a part number that I can get for the upgrade kit that is no longer sold to see if I can locate one through a 3rd party?  This bit of news has really put me in a jam since we have maxed out storage space but the SAN is still more than adequate for our needs, just needs more space.  Thanks.

    Bill

  • Dev Mgr

    6 Operator

    •

    9308 Posts

    •

    3 Points

    1637

    0

    Posted October 28th, 2010 19:00

    Assuming you're on a modern firmware, you can very easily add a PS4000E to the group. This would allow expanding the storage space and eventually even move over completely to the newer system.

    As for the 750GB cap; I've never seen the list of drives that shipped on older Equallogic systems, so I didn't know what would work and only assumed 2TB because the same firmware that works on the newer systems can be applied to the older systems.

    However, currently sold Equallogic boxes don't seem to offer much in the sense of storage space upgrades other than if you bought the system with 8 drives and expand by adding another 8 (identical) drives.

  • Joe S586

    9 Technologist

    •

    729 Posts

    1637

    0

    Posted October 29th, 2010 13:00

    Bill,

    We’re sorry for the inconvenience.  After the acquisition and when we moved over to the 16-drive chassis, Dell did heavy, extensive outreach to all EqualLogic customers with these types of 14-drive arrays advising of a deadline to purchase additional drive packs, or upgrade kits.  We’re sorry you weren’t able to purchase during that time window. We no longer have drive upgrades for sale on those arrays.   Parts are available only for replacement of individual drives in arrays under support contract until April 18th 2013.  There are no upgrade kits available through third parties.  We’d recommend talking to your sales team about adding another array, perhaps a PS4000E which might meet your needs for additional capacity.

    Regards,
    Joe

  • Icb3a

    3 Posts

    1637

    0

    Posted December 2nd, 2010 07:00

    Hi,

     

    Dell JOE can you explain me how the upgrade works please.

     

    If we replace equalogic disk by some larger equalogic certified, does we need to move the data anywhere or the equalogic will ask to expand the actual RAID ?

     

    For the time we had an Equalogic PS4000 XV with 300 GB SAS and we want buy 600GB.

     

    Does it will work ? Have you a document with the procedure ?

     

    Thanks a lot,

    Regards.

     

     

  • Icb3a

    3 Posts

    499

    0

    Posted December 2nd, 2010 10:00

    Joe,

     

    Thanks for the document. I found out some precious informations. But I can't find some answer :

    Does the array will be able to grow after we change the all disks or does it work with the old size ? (sorry if it's à little bit stupid... just to be sure)

    If not is there another sollution ?

    For remember today we have 16 * 300 GB and we want to buy 16 * 600 or higher

    Where can I find the upgrade kit for the PS 4000 XV? I look for in equalogic website, dell and google but nothing...

     

    I really thanks you Joe,

    Regards.