UNSOLVED

jparadis1

updated

17 years ago

J

jparadis1

13 Posts

0

6482

November 30th, 2009 06:00

WWN starting with 25

Sorry for the newb question. In Navisphere I received a bunch of errors this morning like the one listed below. Normally I would be able to find the problem tracing the WWN number, but in this case I stumped. What device's WWN number starts with 25? Usually if the device is a HBA it will start with a 10, a switch it will start with 20 and storage 50. If you can help thanks.

Server (20:02:00:0D:EC:39:18:01:25:11:00:0D:EC:39:18:00) has some HBAs that are active (logged in) but not registered with the storage system. Active (logged in) but unregistered HBA connections are not able to access LUNs on the storage system.

  • jparadis1

    13 Posts

    1570

    0

    Posted November 30th, 2009 07:00

    Kelleg,

    Thanks for your reply. I'm having a problem finding the switch. The closest I have for a switch is 20:02:00:0D:EC:29:18:00. Non of its active ports have a WWN starting with 25 they all start with 10.

    ~jim

  • kelleg

    6 Operator

    •

    4537 Posts

    1570

    1

    Posted November 30th, 2009 07:00

    Start with the switches - look for the WWN in the logged in state on the switches to get the physical port number that the cable is plugged into, then trace the cable back to the device. The WWN starts with 20:02 - maybe Emulex?

    20:02:00:0D:EC:39:18:01:     25:11:00:0D:EC:39:18:00

             NODE                                     PORT

    glen

  • kelleg

    6 Operator

    •

    4537 Posts

    1570

    1

    Posted November 30th, 2009 08:00

    Have you chec ked on the array to see if there is a connected device with this number - go to Connectivity Status and click on the WWN column (left most) and see if it's listed. That will provide you with the SP port that the device is connected to on the array and from there you should be able to trace that back to the switch.

    glen

  • AranH1

    2163 Posts

    1570

    0

    Posted November 30th, 2009 09:00

    Well the WWN is from a Cisco switch.  Cisco's 3 byte code is 00:0D:EC. If you logon to your switches and run 'show wwn switch' it should match up with the what you have listed. Why this is showing up in Navisphere though I am not sure.

    From the Wikipedia entry on WWN:
    First 2 bytes are either hex 10:00 or 2x:xx (where the x's are vendor-specified) followed by the 3-byte vendor identifier and 3 bytes for a vendor-specified serial number.

  • RRR

    6 Operator

    •

    5739 Posts

    1570

    0

    Posted December 1st, 2009 12:00

    > Why this is showing up in Navisphere though I am not sure.

    Could it be one of these span ports ?... I don't know the exact name for this port', but the main purpose is for copying data that flows through all ports..... I guess this port is now acting as an initiator. Does this make sence ? I'm guessing here....

  • AranH1

    2163 Posts

    1570

    0

    Posted December 1st, 2009 13:00

    I was thinking along the same lines as you, there must have been some event on the switch that triggered the switch WWN to attempt to register with the array.
  • RRR

    6 Operator

    •

    5739 Posts

    1570

    1

    Posted December 2nd, 2009 02:00

    I think it's called a SPAN port.
  • jparadis1

    13 Posts

    1570

    0

    Posted December 2nd, 2009 05:00

    Thanks for your help guys. After looking at the sp and switch logs EMC supports thinks that the switches actually logged into the array not an HBA. Its curious that the all the alerts are for switches in the same fabric. I've asked them how do remove the entries in the from navisphere connectivity status and  alerts. So far they don't have an answer for me.

    ~jim

  • Allen Ward

    6 Operator

    •

    2124 Posts

    1570

    0

    Posted December 2nd, 2009 06:00

    If you ever get an answer on this I would love to hear it. I was thinking along these lines as well, but since I couldn't think of any technical reason why a switch port would be logging into an array as an initiator, I just kept my mouth shut (figuratively speaking). This isn't anything I've ever seen before.
  • jparadis1

    13 Posts

    433

    0

    Posted December 2nd, 2009 06:00

    Its a first for me also. Hopefully EMC support will get back to me today.

    ~jim