UNSOLVED

Yvkpatel

updated

1 month ago

Y

Yvkpatel

1 Rookie

•

3 Posts

•

10 Points

0

83

October 14th, 2026 02:05

Aurora R10 bricked after 2.10.0 to 2.9.1 downgrade plus Secure Boot enable - BIOS recovery 3,4 reads USB then hangs

Aurora R10 Ryzen Edition, Ryzen 5 5600X, RX 6800XT, 16GB DDR4, 1TB SSD, board 0TYR0X.

 

I was on BIOS 2.10.0. Secure Boot would show Enabled in BIOS but "Secure Boot State Off" in msinfo32, so I downgraded one version to 2.9.1 using the Dell .exe. Downgrade succeeded. I went into BIOS and it showed 2.9.1.

 

In that same session I went to Secure Boot, enabled it, Save and Exit. After that, the PC never communicated to the display again. No POST, no BIOS screen.

 

Now: fans run, power button blinks amber 3,4 (3 fast, pause, 4 slower, repeat), then it shuts itself off after a couple minutes. Keyboard / USB lights come on when RAM is in DIMM1 (XMM1).

 

What I've tried, all with verified genuine Dell BIOS_IMG.rcv (32MB, checksum matched), FAT32 MBR USB, single RAM stick in DIMM1, SSD removed, rear USB 2.0 port, Ctrl+Esc on power-on:

- 2.10.0 RCV - USB reads, then back to 3,4

- 2.9.1 RCV - USB blinks a lot like it's being read, hangs 5+ minutes with nothing happening, pull power / remove USB / reboot - back to 3,4

- Different monitor / cable, reseated RAM / GPU, CMOS battery

 

I need a real fix, not "try Ctrl+Esc again." Has anyone actually recovered an R10 from this exact state - 2.9.1 plus Secure Boot enable to 3,4 plus recovery hang - without a motherboard replacement? If CH341A is the answer, what is the exact chip location and verified .bin for this board?

 

This is a Dell BIOS bug breaking a working PC. A $500+ motherboard replacement for a Secure Boot toggle is not acceptable.

  • Tesla1856

    10 Wizard

    •

    18086 Posts

    •

    71947 Points

    9

    0

    Posted October 14th, 2026 03:07

    Sounds like you are doing everything correct. But check BIOS Recovery procedures again because there are various directions in later steps.

     

    My (working perfectly fine for years) XPS15-9520 soft-bricked after a common firmware upgrade (that was going fine, until it wasn't). Watched in UEFI-Environment, and it said (in green) Successful. Would then no longer fully Post (stopped at Dell-logo screen).  Yeah, I was just trying to "catch up the BIOS-Firmware" as first step toward SB-CA2023.

     

    Could not get it to Recover BIOS with file on USB. Sounds like yours got further than mine on that.

     

    I ended-up having to extract the ROM with my XGecu T76 Chip-Programmer and a Pogo-Tool. Cleaned it up and load it back in.  

    (edited)

    Dell Rockstar

    Microsoft Windows and Apple iOS Developer (Retired)
    - Like many of you, I can appreciate a good game-engine.
    - I answer questions here, but I'm not a Dell employee.
    - Consider giving posts you like a "thumbs-up"
    - Posting models-numbers and software versions speeds trouble-shooting.
    - Click "Mark as Accepted Answer" on any post that answers your question best.

  • Tesla1856

    10 Wizard

    •

    18086 Posts

    •

    71947 Points

    7

    0

    Posted October 14th, 2026 03:12

    If you can't fix it ... I would not put any more money into it.

     

    Buy yourself a new custom-build. Use GPU, SSDs, and whatever else on new build it you want.  

     

    MSI motherboards are good. They have emergency back-flash button and procedures.

    Dell Rockstar

    Microsoft Windows and Apple iOS Developer (Retired)
    - Like many of you, I can appreciate a good game-engine.
    - I answer questions here, but I'm not a Dell employee.
    - Consider giving posts you like a "thumbs-up"
    - Posting models-numbers and software versions speeds trouble-shooting.
    - Click "Mark as Accepted Answer" on any post that answers your question best.