My new Desktop XPS 8930 come with 16gb DDR4 2666 (2x8) memory. 16go isn't enough for my usage (my old computer has 32), so I bought 2x16gb DDR4 2666 (Kingston HX426C16FB/16) to upgrade the total ram to 48gb (the ideal will be to have 4x16= 64 but it will be for later). Everything is working, the tests are all green, but I have an issue (I don't know if it's normal) : instead of working at 2666MHZ, the 48gb works at 2400MHZ.
Is there something that I have to setup to get my memory full speed?
Below are the memory specs. The only reasons I see that the ram would run at 2400 is if you have an i3 processor installed or the fact that 48GB was not a validated configuration. Did you install them like this = White DIMM 1 16GB, White DIMM 2 16GB, Black DIMM 3 8GB, Black DIMM 4 8GB
Table 1. Memory specifications
Slots
Four UDIMM slots
Type
DDR4
Speed
Up to 2400 MHz: i3 processor
Up to 2666 MHz: i5/i7/i7k processors
Configurations supported:
Per memory module slot
4 GB, 8 GB, and 16 GB
Total memory
8 GB, 16 GB, 24 GB, 32 GB, and 64 GB
The following table lists the available memory configuration matrix:
The Dell BIOS does not have an option to adjust the memory speed or timing. It may just be that with this mix of memory modules the BIOS selected the lower speed. You could try the 32 GB configuration by itself and see what speed you get.
Thank you for this advice, I will try it later, it's a little difficult to unplug everything and test. This test will also allow me to check if I will purchase 2 other 16gb memories to get 64gb next month or not.
Thank you. What do you mean by running dual-channel? The 16gb are working in dual, and the 8gb in single, but in memory tab of CPU-Z it's marked as dual channel, are you talking about that?
My new Desktop XPS 8930 come with 16gb DDR4 2666 (2x8) memory. 16go isn't enough for my usage (my old computer has 32), so I bought 2x16gb DDR4 2666 (Kingston HX426C16FB/16) to upgrade the total ram to 48gb (the ideal will be to have 4x16= 64 but it will be for later). Everything is working, the tests are all green, but I have an issue (I don't know if it's normal) : instead of working at 2666MHZ, the 48gb works at 2400MHZ.
Is there something that I have to setup to get my memory full speed?
Thank you!
Truthfully, I would be grateful it works at all :Smile: ... running 2 different sets like that.
However, since they are matched pairs (and in their own Memory Banks) it should be OK and even run Dual-Channel. I think Dual-Channel is more important than that little mhz difference (both are really fast).
As for the speed, it's common for the motherboard to down-clock the memory a bit as you approach max capacity. And of course, it all has to run at the same speed.
Get yourself a copy of CPUID's CPUz.
Dell Rockstar
Microsoft Windows and Apple iOS Developer (Retired) - Like many of you, I can appreciate a good game-engine. - I answer questions here, but I'm not a Dell employee. - Consider giving posts you like a "thumbs-up" - Posting models-numbers and software versions speeds trouble-shooting. - Click "Mark as Accepted Answer" on any post that answers your question best.
Thank you. What do you mean by running dual-channel? The 16gb are working in dual, and the 8gb in single, but in memory tab of CPU-Z it's marked as dual channel, are you talking about that?
On this motherboard a Memory-Bank consists of 2-slots. An exactly matched pair of DIMMs (in a Memory Bank) should run in Dual-Channel.
A Dual-Channel is a whole another channel or "lane" (like on a highway) as compared to Single-Channel.
Microsoft Windows and Apple iOS Developer (Retired) - Like many of you, I can appreciate a good game-engine. - I answer questions here, but I'm not a Dell employee. - Consider giving posts you like a "thumbs-up" - Posting models-numbers and software versions speeds trouble-shooting. - Click "Mark as Accepted Answer" on any post that answers your question best.
Use Intel Extreme Tuning Utility and go to memory tab and set the profile to XMP. This is what I did with my DDR4 RAM 3000 to get 2933mhz. Before doing that, it was running at 2133mhz (default). Replacing the original memories will void the warranty for specifically that part, but not for other components. Basically, you touch it, you own it, and it is no longer Dell's problem.
While many agree that one should not use this software for overclocking your CPU as it may conflict with your bios settings, it is unknown if you can say the same for the memory. As long as you are not pushing the limits of the RAM which may cause system instability, you should be fine. In my case, all I am doing is enabling the XMP profile as if my bios had it in the settings, which is more or less the same. You can use programs like Prime95 or MemTest64 which will test the ram stability.
RedaSaiko
1 Rookie
•
7 Posts
7739
0
Posted April 13th, 2018 07:00
My CPU is i7-8700 (not K).
The two original memory )8gb) are in the white channel, and the additional ones (16gb) in the black channel.
8gb :
16gb: