UNSOLVED

andy_yang

updated

15 years ago

A

andy_yang

18 Posts

0

4123

March 29th, 2012 03:00

Unable to connect to SPA/B via CS0/1 on public network

Good day,

Recently we procure a VNX5700 with dual CS.

The array was initialized and IP addresses have been assigned to both CSs and SPs.

I am able to ping/connect to the CSs however I was not able to ping/connect SPs.

CS0 - 10.117.13.80

CS1 - 10.117.83.81

SPA - 10.117.13.82

SPB - 10.117.13.83

When I ssh into CS0 and ran

#./setup_clariion -check_and_update -all

Found CLARIION(s) CKM001146010xx

Setup CLARiiON CKM001146010xx storage device...

System 10.117.13.82 is up

System 10.117.13.83 is up

Clariion Array: CKM001146010xx  Model: VNX5700  Memory: 18432

Validating CKM001146010xx storage group '~filestorage'

Setup of CLARiiON CKM001146010xx storage device complete.

and Ping from CS0 to SPA

[root@MTB-VNX-056-CS0 sbin]# ping 10.117.13.82

PING 10.117.13.82 (10.117.13.82) 56(84) bytes of data.

64 bytes from 10.117.13.82: icmp_seq=1 ttl=128 time=0.190 ms

64 bytes from 10.117.13.82: icmp_seq=2 ttl=128 time=0.177 ms

From above, SPA and SPB IP addresses are set correctly.

If I tried connect to the array via CS0's mgmt port, I was able to connect to SPA/B.

(Only if connect to the CSs directly)

The network guy said I must tried set a VLAN tag on the SPs which I managed to do that via naviseccli

After I set VLAN tag on SPs' virtual port 0, no communication is possible.

Apology as I am not a netwrok guy. Only storage I do.

Please assist.

  • dynamox

    11 Legend

    •

    20419 Posts

    •

    87439 Points

    837

    0

    Posted March 29th, 2012 05:00

    can you ask him to un-tag the port on the switch and configure it as normal "access" VLAN ..also remove the tag in Navisphere.

  • andy_yang

    18 Posts

    837

    0

    Posted March 29th, 2012 05:00

    I have done un-tagging on the SPs.

    The network guy show me what was configure on the switch side.

    Its an access vlan.

    He suggest I setup a vlan tag on the CS side.

    I still dont know how I am able to do that.

    I couldnt find any document on setting vlan on cs

  • dynamox

    11 Legend

    •

    20419 Posts

    •

    87439 Points

    837

    0

    Posted March 29th, 2012 05:00

    you don't need tagging for CS and SP ..it's not like datamovers where you can tag to use the same NIC on different VLANs. I have two 5700, all ports are configured as access VLANs. It sounds like proxy-arp is not passing your requests through the control station to SPs. What is the output from this command:

    /nas/sbin/clariion_mgmt -info

  • dynamox

    11 Legend

    •

    20419 Posts

    •

    87439 Points

    837

    0

    Posted March 29th, 2012 06:00

    not sure if its' the issue ..why is CS1 on different class C network ?

  • dynamox

    11 Legend

    •

    20419 Posts

    •

    87439 Points

    837

    0

    Posted March 29th, 2012 06:00

    looks ok, VLAN ID field is blank ?

    3-29-2012 9-20-35 AM.png

  • andy_yang

    18 Posts

    837

    0

    Posted March 29th, 2012 06:00

    Yes, its left blank

  • andy_yang

    18 Posts

    837

    0

    Posted March 29th, 2012 06:00

    Hi Dynamox

    CS1 is also on the same subnet

    eth3      Link encap:Ethernet  HWaddr 00:1B:21:9D:60:80

              inet addr:10.117.13.81  Bcast:10.117.13.255  Mask:255.255.254.0

              inet6 addr: fe80::21b:21ff:fe9d:6080/64 Scope:Link

              UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1

              RX packets:48167 errors:0 dropped:0 overruns:0 frame:0

              TX packets:227 errors:0 dropped:0 overruns:0 carrier:0

              collisions:0 txqueuelen:1000

              RX bytes:3300147 (3.1 MiB)  TX bytes:25876 (25.2 KiB)

              Memory:81a60000-81a80000

    lo        Link encap:Local Loopback

              inet addr:127.0.0.1  Mask:255.0.0.0

              inet6 addr: ::1/128 Scope:Host

              UP LOOPBACK RUNNING  MTU:16436  Metric:1

              RX packets:2780 errors:0 dropped:0 overruns:0 frame:0

              TX packets:2780 errors:0 dropped:0 overruns:0 carrier:0

              collisions:0 txqueuelen:0

              RX bytes:158248 (154.5 KiB)  TX bytes:158248 (154.5 KiB)

    [root@MTB-VNX-056-CS1 sbin]#

  • andy_yang

    18 Posts

    837

    0

    Posted March 29th, 2012 06:00

    [root@MTB-VNX-056-CS0 sbin]# nas_cs -i

    Host Name               = MTB-VNX-056-CS0

    Version                 = 7.0.51-3

    Location                = system:VNX5700:CKM001146010562007|controlStation::0

    Status                  = OK

    Standby Location        = system:VNX5700:CKM001146010562007|controlStation::1

    Standby Status          = Info 26575634437: Standby Ready

    IPv4 Address            = 10.117.13.80

    IPv4 Netmask            = 255.255.254.0

    IPv4 Gateway            = 10.117.12.1

    IPv6 Address            =

    IPv6 Gateway            =

    DNS Domain              = VODACOMBUSINESS.CO.ZA

    DNS Domain search order = VODACOMBUSINESS.CO.ZA

    DNS Servers             = 41.0.1.1,196.2.53.140

    Session Monitor Timeout = 0 Days

    Session Idle Timeout    = 0 Minutes

    NTP Servers             =

    System Time             = Thu Mar 29 14:56:43 SAST 2012

  • andy_yang

    18 Posts

    837

    0

    Posted March 29th, 2012 06:00

    Hi Dynamox

    Please see below

    [root@MTB-VNX-056-CS0 /]# ./nas/sbin/clariion_mgmt -info

    Public IP address for SPA: 10.117.13.82

    Public IP address for SPB: 10.117.13.83

    Start on boot            : yes

    Current implementation   : Proxy-ARP

    Status                   : Started

  • andy_yang

    18 Posts

    442

    0

    Posted March 29th, 2012 06:00

    Apology for the typo earlier on.

    all IPs are on 10.117.13.x
    subnet : 255.255.254.0
    gw : 10.117.12.1