2. Any currently available SATA hard drive is supported.
3. SATA-1, but SATA-2 hard drives can be installed as they are backwards compatible.
4. You leave the primary hard drive, with the operating system connected to SATA-0 on the motherboard, as is and connect the additional hard drive to the motherboard SATA-2 connector.
Remember to check the system setup, to see if the SATA connector the second hard drive is connected too, is Enabled [on]
Note. With SATA there are no Slave/Master settings, like IDE drives, but, the primary 'Boot' hard drive must always be connected to the motherboard SATA-0 connector.
I am trying to retrive data from the 2nd sata drive I configured it as Drive 1 and I have a good SATA drive as drive 0 and I can see it on my BIOS under my Drives but the cOptiplex GX280 tries to boot from drive 1 which the bad drive I can't understand why. From Boot Sequence menu in Bios I have CD/ROM and then SATA (it said installed at first and after the installing the 2nd drive it say not installed) I do have the most updated BIOS version. Thanks in advance for any suggestions.
I took the bad SATA drive with XP Pro (making clicking sounds and the error Boot Device Not Found) from a GX280 and installed it as a 2nd Sata drive1 in a different GX280 with Xp Pro which also has a SATA drive0 and I configure th BIOS to Drive1 on but when I reboot the computer I get an error saying boot device not found hit F1 to continue or F2 for setup. When I go to setup I see both the SATA drives but when I go to Boot Sequence menu it says that there are no SATA drives Installed. I unplugged the bad drive and it boots normally from Drive0. I am hoping if I can boot he computer with bad drive as a secondary drive then I maybe able to retrive data that is if it is not a harware failure. I booted with the GX280 driver/tool cd and tried to run Hard Drive diag and it could not find the drive and the repair failed too from the XP cd. Do you think if it is not a HW failure I am on the right track trying to run the 2nd SATA drive and retrieve data. I know there is no Master/Slave in SATA. What r my other options besides taking it to the data restore place and big bugs? Thanks so much for your help.
Looks like the 'Bad' hard drive is toast, you would seem to be out of luck, with recovering the files and folders yourself and require the services of a data recovery company.
I think so too. That's too bad this person did not back up his stuff. Have you ever taken a hard drive a part and try replacing the hardware from another good drive? I have another identicle drive and may give it a shot since they are 5 years old I am not going to put it back in production. I will keep you updated. Thanks for your help. Take care!
Im having a similar problem adding a 2nd HD (Sata)
Is there a Dell Utility you recommend ?
Thanks
lsuedulive
If your system is a Dimension 5150 and using XP.
Maybe the following can help, if not please describe the problem with installing a second SATA hard drive.
How to add an additional SATA hard drive to the E510.
There should a spare SATA power connector inside the CASE, either P3 & P5, connect the data cable to the motherboard connector SATA2
For the hard drive installation instructions, go HERE <ADMIN NOTE: Broken link has been removed from this post by Dell>.
You will need a 22" [or longer] x 180* x 90* [right angle] SATA data cable, similar to THIS
After the internal hard drive is installed, enter the setup and check that the drive is set to auto [on]. In order for windows to recognize the second hard drive, it must be partitioned and formatted.
THESE are generic instructions for installing an additional hard drive using Windows XP Disk Management, they are by Seagate, but apply to all brands.
shesagordie
12 Elder
•
46017 Posts
1004
0
Posted April 17th, 2009 14:00
media49
1. Western Digital.
2. Any currently available SATA hard drive is supported.
3. SATA-1, but SATA-2 hard drives can be installed as they are backwards compatible.
4. You leave the primary hard drive, with the operating system connected to SATA-0 on the motherboard, as is and connect the additional hard drive to the motherboard SATA-2 connector.
Remember to check the system setup, to see if the SATA connector the second hard drive is connected too, is Enabled [on]
Note. With SATA there are no Slave/Master settings, like IDE drives, but, the primary 'Boot' hard drive must always be connected to the motherboard SATA-0 connector.
5. Either 16mb, or 32mb.
Bev.