UNSOLVED

terrywfoster

updated

21 years ago

0

5171

November 14th, 2005 12:00

Dell Disk Monitoring - OFF

I want to turn this feature OFF.  I do not care about my users seeing a message about a hard drive going out.  If it goes out I want it to go out and not let everyone know for a month before.  Data recovery is not an issue at all.  Users are intructed to back up and if they do not it falls on them when a loss occurs.
 
Again, is there a way to turn this feature totally off on an OptiPlex.  I have no use for this feature and do not want it.
 
Terry W. Foster
 
 
  • 340

    0

    Posted November 14th, 2005 12:00

    Which model(s)?  Certainly on most older Dells it is a feature you CANNOT turn off....
  • 340

    0

    Posted November 14th, 2005 13:00

    GX 260, 270, 280, & 520
  • speedstep

    11 Legend

    •

    46969 Posts

    340

    0

    Posted November 14th, 2005 17:00

    SMART cannot be turned off.
  • 340

    0

    Posted November 14th, 2005 19:00

    That is enough to make me swap to another brand of PC's.
  • speedstep

    11 Legend

    •

    46969 Posts

    340

    0

    Posted November 15th, 2005 08:00



    @terrywfoster wrote:
    That is enough to make me swap to another brand of PC's.





    I guess you ask your car dealer to remove the OIL and CHARGE and TEMP lights in your car also.
    Sounds like support personnel that don't want to be bothered trying to support users that don't know about hardware and would rather give them pain and suffering instead of help and support.
  • 340

    0

    Posted November 15th, 2005 12:00

    It is just a useless annoyance.
  • speedstep

    11 Legend

    •

    46969 Posts

    340

    0

    Posted November 15th, 2005 15:00

    If its so annoying you could get the IDE drive vendor to turn this feature off in the hard drive bios.

    Microsoft talks about disabling this via WMI but I don't know if that applys here.


    http://www.microsoft.com/whdc/archive/smartdrv.mspx

    By default, WMI polls the hard disk periodically; this polling frequency can be configured using a WMI (WBEM) method call, for example, ExecMethod or ExecMethodAsync.

    For IDE, this polling consists of sending the READ_SMART_STATUS command. If this status indicates an error, a WMI event will be launched that includes the SMART attribute data. There are also WMI (WBEM) classes that will cause the SMART status and attribute data to be returned when queried.

    S.M.A.R.T. (Self Monitoring Analysis and Reporting Technology):
    This technology provides users with advanced warning of Disk Drive failures thus enabling the Operating System to warn Users of potential failure. S.M.A.R.T. was included in EIDE drives with the ATA-3 specification.

    Windows: "Where do you want to go today?"
    Linux: "Where do you want to go tomorrow?"
    FreeBSD: "Are you guys coming, or what?"

     

  • t_washburn

    24 Posts

    340

    0

    Posted November 18th, 2005 20:00

    So, S.M.A.R.T. is supposed to warn of a potential failure from within a Windows session?
    Does it do this without any extra conifguration within Windows?  Because we've had 22 hard drives fail over the course of the last year, with a large majority in the last 6 months, and I've yet to get a S.M.A.R.T. warning from within the OS, let alone at boot up.
    I still don't understand why anyone would want to shut this off, there's two of us supporting the roughly 200 client pc's in house and I'd rather be warned ahead of time and be able to replace the hard drive after hours rather than having to interrupt someone's work day with an emergency.
    Almost all of these drives were Maxtor DiamondMax Plus 9 160GB SATA Hard Drives by the way.