UNSOLVED

Vimalan3NZ

updated

4 months ago

V

Vimalan3NZ

1 Rookie

•

1 Message

0

9435

December 12th, 2023 07:49

Avago EFI SAS Driver

Avago EFI SAS Driver
Unhealthy status reported by this UEFI driver without specific error massage 

Server not booting or go to setting keep showing this error massage 

  • DELL-Erman O

    Moderator

    •

    2984 Posts

    •

    14874 Points

    0

    0

    Posted December 12th, 2023 12:05

    Hello,  the “Avago EFI SAS Driver Unhealthy status” error is typically reported when the system detects a problem with the RAID controller or the drives connected to it.

    I don't know which server and PERC you have it but below steps for generic steps.

     

    To access the Avago EFI SAS Driver PERC, enter it and look at the information shown. You will be asked to type a letter. Press 'Y' and enter. 

      
    To exit the Recovery Mode of the LifeCycle Controller:

     
    -Go to F2 -> System Setup -> iDRAC Settings -> Lifecycle Controller to see the status

     
    -Select: Lifecycle Controller set to Enabled

     
    -Collect System Inventory on Restart set to Enabled.

     
    -Cancel Lifecycle Controller Actions set to Yes.

     
     

     
    UEFI0116 usually means a problem with the disk drive.

     
    Perform diagnostics and update drivers and firmware for storage chain: PERC, backplane, hard drives

      

     
    To perform diagnostics:

     
    Boot to  F11 on Dell Splash screen, choose  Boot Manager -> System Utilities -> Launch Dell Diagnostics.  Record any messages and continue testing."

     

    or Disable and Re-enable the Lifecycle Controller: You can disable and then re-enable the Lifecycle controller through the command line. The commands are as follows:

    racadm set LifecycleController.LCAttributes.LifecycleControllerState 0
    racadm set LifecycleController.LCAttributes.LifecycleControllerState 1

    DELL-Erman O

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell

    Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!

  • Miteshskvt

    1 Rookie

    •

    2 Posts

    0

    0

    Posted March 26th, 2024 13:17

    RAID Controller in Slot 6: Dell PERC <PERC H730P Adapter> Driver Health Protocol Utility

    Critical Message

    There are offline or missing virtual drives with preserved cache. Please check the cables and ensure that all drives are present. Press any key to enter the configuration utility.

    Enter Your Input Here:

    i First you might need to press <Enter> to get the input window. Then press the desired key(s) in response to the critical message displayed above... (Press <F1> for more help)

    Please help i am stuck with this message and server is not restarting. 

  • DELL-Marco B

    Moderator

    •

    3980 Posts

    0

    1

    Posted March 26th, 2024 15:49

    Hello,

    the problem comes from any hardware modifications or update?

    Can you share more details? 

    I think it could be an issue with PERC card. Do you have a backup of data?

    I suggest to shutdown the server and reseat all RAID components (perc, hard drives and cables). And restart again.

    Thanks

    DELL- Marco B

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell

    Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!

  • KEROKA TECHICAL TRAINING INSTITUTE

    1 Rookie

    •

    1 Message

    •

    2 Points

    0

    0

    Posted January 10th, 2025 11:33

    @DELL-Marco B​ Done so and still not booting bring back the first black screen 

  • DELL-Marco B

    Moderator

    •

    3980 Posts

    0

    0

    Posted January 10th, 2025 14:57

    @DELL-Marco B Done so and still not booting bring back the first black screen 

     

     

    Can you share more details? The problem comes from any hardware modifications or update?

    It is possible that it is an hardware issue with PERC

    DELL- Marco B

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell

    Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!

  • CaptainAdhoc

    1 Rookie

    •

    2 Posts

    •

    2 Points

    0

    0

    Posted January 18th, 2025 23:27

    @Miteshskvt​ 

    Hello,
    I have exactly the same issue following the update of my PERC card.

    It is impossible to access the BIOS with F2 or do anything else.
    Thank you for your help

    (edited)

  • DELL-Young E

    Moderator

    •

    5421 Posts

    •

    37 Points

    0

    0

    Posted January 20th, 2025 02:55

    Hello, it could be the hardware issue for you as well just like Marco says. https://dell.to/3POasK9 You can also reach out to the region support for a second opinion and hardware replacement.

    Respectfully,

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell

    Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!

  • mnuaimi

    1 Rookie

    •

    2 Posts

    •

    2 Points

    0

    0

    Posted January 23rd, 2025 15:28

    Hello, We have the same problem on
    It was working, we did a reboot and the problem appeared
    Any help?

  • DELL-Marco B

    Moderator

    •

    3980 Posts

    0

    0

    Posted January 23rd, 2025 21:10

    Hello 

    as said before it can be an hardware issue. Can you contact support for this?

    DELL- Marco B

    Social Media and Communities Professional

    Dell Technologies | Enterprise Support Services

    #IWork4Dell

    Did I answer your query? Please click on ‘Mark as Accepted Answer’. ‘Thumbs up’ the posts you like!

  • CaptainAdhoc

    1 Rookie

    •

    2 Posts

    •

    2 Points

    0

    1

    Posted January 23rd, 2025 21:26

    Hi everyone,

    I wanted to share the solution that worked for me:

    1. I powered off the server.

    2. Then, I unplugged the PERC card.

    3. This allowed me to access the Lifecycle Controller.

    4. Once there, I disabled UEFI mode and switched to BIOS mode.

    5. I powered off the server again and reconnected the PERC card.

    6. Finally, I re-enabled UEFI mode.

    Everything went back to normal after these steps. I hope this works for you too. Best of luck!