rhoninpowers

updated

14 years ago

0

88824

July 2nd, 2012 15:00

Intel x520-t2 NIC problem on Windows Server 2012 (Nic keeps disconnecting/reconnecting constantly)

I just installed 2012 RC on my R815, it has 2 Intel x520-t2 nics on a PowerConnect 5548 Switch.  The NICS continue to "bounce" between connect/disconnect.  I was pointed to Dell since I purchased the nics through you.  I read the 2012 documents from Dell and these nics are said to have been tested and the inbox drivers should work.

 

Can someone please tell me if there's a config change that I need to make?

 

thanks.

 

 

 

  • Daniel My

    12 Elder

    •

    6204 Posts

    6633

    1

    Posted July 3rd, 2012 13:00

    There does not appear to be an issue with the switch. I would still recommend that all interfaces connected to computers/servers be in access mode.

    At this point I would check to see if it is an OS/driver issue, or a hardware problem. I would recommend booting to a Linux live DVD or some other OS that you can test the NIC's with. If you encounter the same problem with another operating system then there may be a firmware update that needs to be performed, or a hardware malfunction.

    If you do not encounter the same problem with another OS then it would appear to be an OS or driver issue. Given that this is a beta OS there is not much we can do with that. Here is our OMSA live DVD that you can use for testing. It is a distro of CentOS:

    http://linux.dell.com/files/openmanage-contributions/omsa-65-live/OMSA65-CentOS6-x86_64-LiveDVD.iso

    Thanks

  • 6610

    0

    Posted July 3rd, 2012 11:00

    Hello Daniel,

    Thanks for responding.  There are not any port configurations on the switch yet.  Just completed the initial setup and only enabled jumbo frames on the switch.  Strange I "think" I may have already tried that driver on my WServer2012 machine (said was not for this os), but I will download again using the link you gave me and update this thread immediately.  I disabled jumbo frames on the NIC as a test but that did not make a difference. 

  • Daniel My

    12 Elder

    •

    6204 Posts

    6610

    0

    Posted July 3rd, 2012 11:00

    Hello rhoninpowers

    If you would like to provide the configuration of the interfaces that the NIC is attached to on the switch I will let you know if there are issues. Also, let me know if you have the NIC configured for LACP or any other advanced features. Since this is a beta operating system the driver included with the OS is probably the best to use. If that driver is causing problems then you can try the latest we have available:

    http://downloads.dell.com/FOLDER00410451M/1/Network_Driver_8D5KK_WN32_13.5.0_A00.EXE

    You can get the interface information by performing a show run, or running:

    show interfaces configuration

    or

    show interfaces configuration gi1/0/1

    If you do not specify an interface it will show the information for all interfaces.

    Thanks

  • Daniel My

    12 Elder

    •

    6204 Posts

    6633

    0

    Posted July 3rd, 2012 12:00

    Okay, let's try to narrow down the problem.

    You have the NIC connected to the 1GB ports and not the 10Gb uplink ports correct?
    Is the NIC correctly auto-negotiating to 1Gb?
    Have you tested the switch with another NIC to verify it is functioning?
    Have you tested the NIC with another switch/router?

    If we can rule out a hardware or configuration issue then it becomes a driver problem. If that is the case then you will likely have to wait for the driver supplied to Microsoft to be updated.

    Thanks

  • Daniel My

    12 Elder

    •

    6204 Posts

    6633

    0

    Posted July 3rd, 2012 12:00

    From the guide I have the HDMI Port 2 on the top switch and HDMI port 1 used on the bottom switch to link and manage together....should I reverse them or???

    That is fine.

    Let's see if spanning tree is blocking any ports. Run this command and post the output:

    #show spanning-tree

    After you copy the output then make sure the interfaces connected to the NIC are in access mode. This will remove any VLAN tagging and should also cause them to not be blocked by RSTP. Here is an example of how to put an interface into access mode:

    Console(config)# interface gigabitethernet 1/0/1
    Console(config-if)# switchport mode access

    Thanks

  • 6610

    0

    Posted July 3rd, 2012 12:00

    Update:  I tried the driver pack and it is the one that I had downloaded and tried.  I tried this to be sure and got the error message that the package was not for Windows Server 2012.

    Serial connection (Top Window) shows links bouncing and Port config (bottom window) shows the port config (nothing changed.)

    Machine generated alternative text: çCOK1-Puffl L-flfl
03—Jul—2012 10:49:09 %LINK—W—Down: gi2/0/1
03—Jul—2012 10:49:12 %LINK—I—Up: gi2/0/1
03—Jul—2012 10:49:13 %LINK—W—Down: gi2/0/32
03—Jul—2012 10:49:16 %LINK—I—Up: g12/0/32
03—Jul—2012 10:49:18 %LINK—W—Down: gi2/0/1
03—Jul—2012 10:49:21 %LINK—I—Up: gi2/0/1
03—Jul—2012 10:49:22 %LINK—W—Down: gi2/0/32
03—Jul--2012 10:49:25 %LINK—I--Up: gi2/0/32
03—Jul—2012 10:49:27 %LINK—W—Down: g12/0/1
03—Jul—2012 10:49:30 %LINK—I—Up: gi2/0/1
03—Jul—2012 10:49:31 %LINK—W—Down: gi2/0/32
03—Jul--2012 10:49:34 %LINK—I--Up: gi2/0/32
03—Jul—2012 10:49:36 %LINK—W—Down: gi2/0/1
03—Jul—2012 10:49:39 %LINK—I—Up: gi2/0/1
03—Jul—2012 10:49:40 %LINK—W—Down: g12/0/32
03—Jul—2012 10:49:43 %LINK—I—Up: gi2/0/32
03—Jul—2012 10:49:45 %LINK—W—Down: gi2/0/1
03—Jul—2012 10:49:49 %LINK—I—Up: gi2/0/1
03—Jul—2012 10:49:49 %LINK—W—Down: g12/0/32
03—Jul—2012 10:49:53 %LINK—I—Up: gi2/0/32
03—Jul—2012 10:49:55 %LINK—W—Down: gi2/0/1
s03—Jul—2012 10:49:58 %LINK—I—Up: gi2/0/1
03—Jul—2012 10:50:02 %LINK—W—Down: gi2/0132
I -

    Machine generated alternative text: Summary Edit
Port UntO. [igii/oii 2]
Description (0-6.4 Characters) I
Port Type 10001.1-copper
Admin Status Up J
Current Port Status Down
Re-Activate Suspended Port F
Operational Status Active
Admin Speed 1000l j
Current Port Speed
Admin Duplex IFuil j
Current Duplex Mode
Auto Negotiation Enable
Energy Efficient Ethernet Enable ] W Energy Efficient Ethernet LLDP
Short-Reach Energy Saving Disable z]
Current Auto Negotiation
Admin Advertisement W Max Capability F 10 Half F 10 Full F 100 Half F 100 Full F 1000 Full
Current Advertisement Unknown
Neighbor Advertisement Unknown
Back Pressure Disable
Current Back Pressure
Flow Control Enable
Current Flow Control
MDVMDD( lAuto 2]
Current MDLIMDD(
LAG

  • 6610

    0

    Posted July 3rd, 2012 12:00

    On the server the error is on the ixgbi and will go back between connecting/disconnecting as mentioned

  • 6633

    0

    Posted July 3rd, 2012 12:00

    Ok this is strange but
    first to answer your questions:
    Yes the nics are plugged into
    1GB ports (I have one port plugged into both switches)...the switches are
    combined via the HDMI cable.  both switches are Powerconnect 5548.s
    The servers have 6 nics (the quad port LOM that came with system works fine)
     
    it looks like it may be a
    problem with STP?  the switch appears to have disabled one of the nics and
    the other nic in the OS seems to be stable???!!!!
    Here's a graphic (above) showing STP status...  (I can now only see one nic as active on the
    server...like the switch disabled.)
    The NICS have the RJ45 connections (10BASET I guess???) but I could not plug them into the uplink
    ports.
     
    From the guide I have the HDMI Port 2 on the top switch and HDMI port 1 used on the bottom switch to link and manage together....should I reverse them or???
     
  • 1108

    0

    Posted July 3rd, 2012 13:00

    I disabled one of the nics...and the other nic grabbed an IP and stopped bouncing.  It does look like a driver issue.  Thanks for the link...I did not read closely...sweet!!!!  although I could fill a book with OMSA questions.  thanks.

  • 1108

    0

    Posted July 3rd, 2012 13:00

    Ahhh yes...I actually just downloaded that (Centos) a few days ago to do some Hadoop testing.  2 questions before I go...how do I surpress the updates in the serial window on the switch and is there a way to "redirect" that output over the network so I can view from other machines?  (I don't log into switches much and I am really rusty...wow.  :)

    thanks for the help.