pereubu

updated

17 years ago

P

pereubu

86 Posts

0

9966

September 28th, 2009 05:00

NetWorker and the inquire command are not seeing the ADIC Scaler 24 Jukebox

ADIC Scalar 24 310A|Autochanger

NetWorker and the inquire command are not seeing the ADIC Scaler 24 Jukebox

Operating system is MS 2003 sp1.

What can i do?
  • HacknDos1

    1 Rookie

    •

    66 Posts

    3881

    0

    Posted October 1st, 2009 10:00

    Based on a lot of things that have been said here there is several things you should check.

    1) Zoning is setup proper
    2) Switch is hard set for 4gb and not on Auto
    3) Are the tape drives in use when you are trying to do this? (belive it or not this matters.)

    Inquire although useful, will display different information back to a server connected to the same drives, if those drives are in use on a different server. So make sure none of the hardware is in use.

    I myself have tried to setup drives on a storage node in the past, and scratched my head as to why doesn't the server see them, and why arent they appearing in inquire, only to come and find out they were in use.

    4) Open your HBA software and see if the drives appear there. If they don't, or only one of them does. You need to go back to the switch. OS won't see them if the HBA can't see them.

    Paul
  • HCLBACKUP

    2 Intern

    •

    150 Posts

    3897

    0

    Posted September 28th, 2009 05:00

    Are you able to see the drives in Device manager.

    I think the drives and library is not visible at OS level itself.
  • pereubu

    86 Posts

    3897

    0

    Posted September 29th, 2009 02:00

    I am able to see only one tape drive like IBM ULTRIUM. I should have ADIC drive for jukebox as, and second IBMUltrium drive. The idea is that this driver has to install by itself I guess.
  • amediratta

    2 Intern

    •

    2014 Posts

    3897

    0

    Posted September 30th, 2009 02:00

    Well yes, Windows install drivers itself provided it is able to detect the devices. For each Autochanger you should have a medium changer and all the devices connected to the server. You can try and rescan for hardware changes to be sure.

    If it is not there, check the hardware connectivity. reboot the server and check during boot process on the SCSI card if I think cabling is OK.

    I would also recommend installing latest Autochanger & device manufacturer drivers instead of relying on Windows drivers.
  • pereubu

    86 Posts

    3897

    0

    Posted September 30th, 2009 03:00

    "If it is not there, check the hardware connectivity. reboot the server and check during boot process on the SCSI card if I think cabling is OK"

    Ok with drivers, but I have checked Connectrix and zone for that, and it seems to be OK. HBAnywhere as well. But what about SCSI card? I have on Device Manager SCSI and RAID controllers and there is EMS Device bus.

    Briefly I do not have knowledge to know how to check cabling on SCSI card!
  • PeterBen

    120 Posts

    3897

    0

    Posted September 30th, 2009 04:00

    you need to know how is the library connected to your server. if it has worked before you have a device or cabling malfunction. if it is the first time setup most likely you have improper cabling or zoning. use the HBA or SCSI tools to scan the controller for the devices. once you see it there it will be in device manager. until you can see it in device manager you do not need to try to resolve it on networker level.
  • HacknDos1

    1 Rookie

    •

    66 Posts

    2545

    0

    Posted September 30th, 2009 11:00

    If your using Fiber drives. You need to assign one of the drives as the controlling drive. Least thats what I did in my Dell Branded ADIC i500 scalar library.

    If this tape drive that is the controller is not presented to the server (Management Server or Storage Node), server won't see the library. Only server to see the library would then be the machine that has that tape drive presented to it. (Zoned to that server)

    Hope this helps.

    Paul
  • aismaili

    25 Posts

    2545

    0

    Posted September 30th, 2009 18:00

    what is the error (if any) inquire reporting when you run this command. You may be able to configure your jukebox using the sji option

    4) Configure an SJI Jukebox

    Try that and let us know.
  • amediratta

    2 Intern

    •

    2014 Posts

    3897

    0

    Posted October 1st, 2009 00:00

    Since you did not mention whether library is SCSI or FC, I assumed it to be SCSI. If it is FC, you do not need to check that. All you need on OS is to make sure you get the library robotics and the tape devices as medium changer & Tape Drives in the Device Manager. Library Robotics is mandatory only if this server is controlling the robotics.

    Run the inquire command and check if you get the robotics and drives there. If not clear to you, post the output here.
  • pereubu

    86 Posts

    3910

    0

    Posted October 1st, 2009 06:00

    No, It is FC.
    C:\Documents and Settings\aleksandar>inquire -t
    scsidev@0.0.0:DGC RAID 5 0326|Disk,
    S/N: C
    WWNN=6

    PORT=0
    scsidev@0.0.3:DGC RAID 5 0326|Disk
    scsidev@0.1.0:DGC RAID 5 0326|Disk
    scsidev@0.2.0:DGC RAID 5 0326|Disk
    scsidev@0.3.0:DGC RAID 5 0326|Disk
    scsidev@0.4.0:IBM ULTRIUM-TD3 64D0|Tape
    scsidev@5.0.0:DGC RAID 5 0326|Disk
    scsidev@5.0.3:DGC RAID 5 0326|Disk
    scsidev@5.1.0:DGC RAID 5 0326|Disk
    scsidev@5.2.0:DGC RAID 5 0326|Disk
    scsidev@5.3.0:DGC RAID 5 0326|Disk

    The same thing is on the Device manager. This is new computer and it is storage node. It works only for one drive (device). I have installed Ultrium Driver.

    Microsoft Windows [Version 5.2.3790]
    (C) Copyright 1985-2003 Microsoft Corp.

    C:\Documents and Settings\mb_admin>inquire -t
    scsidev@0.0.0:DGC RAID 10 0326|Disk, \\.\PHYSICALDRIVE0
    S/N: CK200071900247
    WWNN=6006016049AD1C001CB0F2F72035DC11

    PORT=00000001
    scsidev@0.0.1:DGC RAID 5 0326|Disk, \\.\PHYSICALDRIVE1
    S/N: CK200071900247
    WWNN=600601602BC41D004D6E42E4F077DC11

    PORT=00000001
    scsidev@0.1.0:DGC RAID 10 0326|Disk
    scsidev@0.2.0:DGC RAID 10 0326|Disk
    scsidev@0.3.0:DGC RAID 10 0326|Disk
    scsidev@0.4.0:IBM ULTRIUM-TD3 64D0|Tape, \\.\Tape0
    S/N: 1210266394
    ATNN=IBM ULTRIUM-TD3 12102663
    94
    WWNN=500308C175E80426
    WWPN=500308C175E80427
    PORT=00000001
    scsidev@4.0.0:DGC RAID 10 0326|Disk
    scsidev@4.0.1:DGC RAID 5 0326|Disk
    scsidev@4.1.0:DGC RAID 10 0326|Disk
    scsidev@4.2.0:DGC RAID 10 0326|Disk
    scsidev@4.3.0:DGC RAID 10 0326|Disk
    scsidev@4.4.0:IBM ULTRIUM-TD3 64D0|Tape, \\.\Tape1
    S/N: 1210266406
    ATNN=IBM ULTRIUM-TD3 12102664
    06
    WWNN=500308C175E80423
    WWPN=500308C175E80424
    PORT=00000001
    scsidev@4.4.1:ADIC Scalar 24 310A|Autochanger (Jukebox), \\.\Changer0
    S/N: ADIC_1_C00027529

    C:\Documents and Settings\mb_admin>
    That one is storage node as well, but I can have two devices (two drives on the jukebox) from this server.The Device Manager gives drive for a changer and two drives for tape. Therefore I can have two devices for each old sever configured as a storage node.